I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hi All,
I have this strange problem with setting the RAM rentention. This code used to work fine on my old PCB but I have made a new PCB which is almost identical to the...
I am trying to get this working with GCC, and I use github.com/.../nrf51-pure-gcc-setup as a base.
I am not too sure how all this works together but:
Can these SDKs...
Can't set tx power level using sd_ble_gap_tx_power_set(tx_power) in S130.
Is there something special I must do? I'm trying to use this function to set the power to any...
Hi, I'm having a problem with registering more than one pstorage_handle_t. So far I believed that I can register as many pstorage_handle_t as I want, but the number of these...
Has anyone had success with a J-link ARM v7 with the nRFgo studio (and nRF51822)? I've got one of the older nRFgo moterboard dev kits, and I've been doing well with the included...
Hello,
I am working on a product, which uses the nRF8001 as basis for the Bluetooth communication. The application offers two interfaces, a custom interface and a HID interface...
Hello,
I have a problem with Indicate Characteristic. When I try to send data using sd_ble_gatts_hvx() function, it always sends 20bytes from address 0x00. This is my code...
I am trying to run my program once per second using timer. The timer is initialized as follows:
APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_MAX_TIMERS, APP_TIMER_OP_QUEUE_SIZE...
I'm trying to figure out how the bonding works in the multilink demo. It seems like the central device only goes through the bonding if the peripheral has the multilink service...
ble_app_uart_s110_pca10028_nuevo.uvprojx
Hi, I´m using a nRF51244 with s110. I program it in nRFgo Studio (s110_nrf51_8.0.0_softdevice.hex)
I try turn on the passkey...
Hi,
I performed an OTA update of my APP. (SD 7.0 and BLE single bank bootloader were flashed).
The update finished without an error and then my application even starts,...
Hi,
I'm developing on a custom nrf51822-based board, and using the s110 softdevice, version 7.0.0. With JLinkGDBServer and the toolchain's gdb, I can debug softdevice-less...
