I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
My issue is that even when using...
Hi All,
I am building a event driven IoT application thus using the Nordic CAF I like to know if the Nordic and/or zephyr (system) threads are running fine (if not the watchdog...
Hello,
I am currently migrating from NCS 2.6.0 to NCS 2.7.0 on my board with an NRF9160.
During that process I switched to the new hardware model and to sysbuild. As far...
Hi,
I am getting the following error: CMake Error at C:/ncs/v2.6.1/zephyr/cmake/modules/extensions.cmake:2891 (message):BOARD is not being defined on the CMake command-line...
Dear Team,
This is my first embedded project.I am basically from Analog design background.
I connected the nRF52840-DK board as shown below.
I connected the board...
Hello and thanks for reading. Our device needs to act as both a central and peripheral. I have written all the peripheral code, and its all working perfectly. However, once...
Hi,
I have a project in which I'm using the nRF52840 with OpenThread and the device is configured as an MTD to minimize power usage. I have recently updated my nRF Connect...
Hi All, I am getting build errors for a project. Project specifics below: - nRF52832 (custom board) - NCS v2.6.0 - Custom board files and other configuration files attached...
My application is running on a nRF9160 using NCS v1.7.0 and modem FW 1.3.0. Sometimes, when our device is in an area with bad LTE coverage, I believe we're overflowing some...
Hi there,
I am using the NRF52840DK development board as a learing experience. I have used the EXCERCISE8 on the Nordic learning program and created a SPI driver for a simple...
Hi all, I am observing some strange behaviour on my two nRF52840 devices. They are running NCS v2.1.0 (Zephyr 3.1.99), one as central and peripheral, one as peripheral only...
Hi,
I am trying to build the pc-ble-driver library from source following the readme instructions ( https://github.com/NordicSemiconductor/pc-ble-driver ) on my Windows...
Hi,
MCU: nrf52840
SDK: nRF5_SDK_17.1.0_ddde560
I am facing such an issue, sometimes after the device's OTA success, and then I would like to upgrade to another version...
Hi. I'm on a relatively old ryzen-5 windows 11 PC and I get 30 FPS when recording power with Power Profiler version 4.0.0 and 2 FPS when recording with newer versions (4.1...
Dear Nordic support team,
I cannot enable the Nordic specific HCI command to enable the HCI survey, I always get the following error with NCS v2.6.1:
For information...
