Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
HI,
Following is the procedure to flash application we have tried:
Mass Erase
Write bootloader start address
Flash soft device
Flash bootloader
Flash application...
Hi,
I'm use ncs sdk what to send ADV_EXT_PDU Advertising, but this PDU every time send 8 advertising event, however, i'm notice that ncs sdk only use 8 second advertising...
I have a product under development that needs to send USB key codes to the PC that are outside the range that is supported by the USBD library and I am wondering the best...
Hi,
I´m developing a BLE-OTA driver for a BLE SoC and I try to use the nRF52840 dongle with my PC as the second device for the OTA mechanism by using Python and the pc_ble_driver...
I'm trying to create a HAL library to use it with zephyr application
From what I have read I need to create another module .
I can't figure out how to set up the module...
I am using the nRF52840-dk with the nRF Connect SDK v2.0.0 and for the development itself I use Visual Studio Code.
My Goal: Both the bootloader and the actual application...
Hi,
In my project, I have finished the application core code.Then I need to debug net core, but when I selected the "hci_rpmsg" target,and click the debug button.The debugger...
Hello my question is I am giving supply with lithium 18650 battery whic voltage is 3.7 to 4.2 volt but the battery falls very much below .
My question is when using HIGH...
Hello,
I'm working with NUS service and the nRF Toolbox app. I need to send multiple messages from mobile app to DK. How can I do that?. Is there a macro/script example...
I'm currently evaluating the nRF52840dk using the nRF Connect SDK to determine whether or not to port over our codebase to it from a Xiao nRF52 module I was using KVStore...
Hi,
I am trying to flash nrf52840 dk board with open thread binaries.
I see that, sporadically the device gets readback protection enabled.
I use the following command...
Hi
I have two PCA10121 and followed the instructions here to get the demo audio application to work.
The output of:
python3 buildprog.py -c app -b debug -d both
is...
I am writing my own code (no libraries etc.) on nRF52832.
For new i still have softdevice and bootloader in flash, and store my program using bootloader protocol, but my...
Hi There!
I'm using the dimmable light bulb example and have extended it with the color control attribute list. I'm using the zb_zcl_color_control_attrs_ext_t in combination...
Hi, I am working with custom board in that, trying to read NTC sensor value using 2 (NTC+ and NTC-) ADC pins. Applied Steinhart formula to convert temperature. In that, After...
