Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
I try to use 52832 as a frequency meter to measure the bluetooth central frequency to do crystal trimming.
The target is a CW(continous wave) signal, like 2441MHz,which...
Hello, I meet some problem. The chip I used is nRF52810 QCAA, the softdevice I used is s112, I defined P0.09 as SCL and P0.06 as SDA, the TWI can't work and it stops in while...
Short Our project runs application code on the nrf5340 application core and a bt_mesh configuration on the network core. Everything works as expected when we build as two...
Hi, I am Marcous.
Recently I am doing the AoA project in the nrf52833 board. I have now got a antenna matrix, sky13322-375LF , a board with four antennas in it and 4 gpios...
Hello i've implemented a push button detection with the bsp library but i can't fin a way to configure a pullup with it :
When i check the tention on the input it's at...
Hi Nordic DevTeam,
What I have learned from this thread below is that using 32kHz external crystal provides less power consumption and better accuracy :
https://devzone...
To the kind Nordic support team,
We are evaluating a scenario where we need a "gzll gzp host" to receive data on two encrypted pipes at almost the same time (we modified...
i was running some power optimization and MTU tests in NCS V1.5.1 and was able to compile and run.
I upgraded to NCS V1.6.0 and there were several errors
So when I compile...
Hello,
I am currently working with the development board nRF5340DK in order to evaluate the nRF5340 SoC.
Given certain project requirements related to the operating temperature...
Hello,
I am new on Nordic controller platform and i want to make the GPIO pull down and pull up at run time and also change the IO direction.
How i can do that please...
I am using the FAT FS on the nRF9160-DK to store data on an SD card.
The CLIB library provides Linix-like fopen, fclose, …
The flags passed to fopen are strings like ...
hello,
i am using nrf52832 with sdk 15.2 using ble_app_uart example and my beacon stops axdvertsing after sometime can someone help me how can make it advertise continosuly...
I am currently evaluating nrf52840 - CDSENET E73-2G4M08S1C module with installed CircuitPython 7.0.0-alpha.3. Unfortunately the ADC readings are quite noisy. For example for...
