I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Hello I have a question, after watching the video: youtu.be/7h4wxyFktkQ It is mentioned that it is not recommended to connect to Google Cloud Platform from a device that is...
Hi, I am running NRF5_SDK_13.0.0_04 and s132_nrf52_4.0.3 on a custom board.
I am getting a Soft Device Fault on an NRF52832 device that I am not able to root cause. This...
Hi,
I downloaded nRF5_SDK_15.3.0_59ac345.
The first time,
Uploaded "..\examples\connectivity\ble_connectivity\hex ble_connectivity_s140_usb_hci_pca10059.hex" by nRF...
So I'm sending multiple payloads of the same width from the transmitter to a receiver and I see it sends only sends 3 times after which `TX_FULL` bit is set in the status...
Hi,
I'm working on a project involving pressure sensors.
These are to be read out via UART and then transmit the data via Mesh to a relay node up to a PC, which visualises...
Dear Sir or Madam, I am asking advice on the following matter: When trying to port the "pin_change_int" example to a nrf52833 DK the code compiles but is not showing the expected...
Hello, I developed a project starting from MQTT-SN example available in SDK for Thread and Zigbee.
I noticed that publishing and subscribing requires calls to functions...
hi，
I work in the nrf5_SDK_for_Mesh_v4.1.0_src. I want to adjust TX power based on light switch server . After setting TX power, I find that RSSI varies from high to low...
Hi.
I'm using nrf52840 SDK 16 with S140.
in my last piece of code static arrays were not enough and i needed malloc.
I used malloc without any issue, also i use cJSON...
Hi I am new to BLE energy and I would like to know if there are any SDK examples I could refer to learn about two DKs to communicate the external sensor data to the central...
Hello Nordic team,
I'm working on an nrf52840 with the SDK 15.3.0.
I'm using the SPIM instance 3 at 32MHz to interract with a Slave SPI which can support up to 40MHz....
Hi my USB keyboard application works on Windows and Linux but not on a MacBook Air with macOS Sierra 10.12.6. So I did step back and tried the combined HID example nRF5_SDK_16...
Hi,
I am using NRF52832 on SDK16 and Mesh 4.1.
When I use the NRF Mesh app to connect to a node, everything just works fine. Whenever I reset the device, the app and...
Hi,
I want to use a timestamp in my payload when ever I send data to the cloud.
First I wanted to use the ntp example from Håkon found here: https://github.com/Rallare...
So I've been tinkering with nrf2401 module lately and trying to send data between the modules. PTX is set up on STM32 and PRX on RPI, and i'm sending from PTX to PRX.
I...
