Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hello,
Is it possible to set the clock source for a timer to the RC oscillator?
I'm using Bluetooth in combination with my timer and I see that it is counting differently...
(Windows10, Android Studio 4.0.1, SDK 15.2.0, nRF52832 dev board, App run on Galaxy S10, latest Android version).
Hi, I'm looking to use the Toolbox to create a template...
Hello,
I am having a few issues with getting the SD card FATFS example code to share the same bus as another slave I transfer data to.
I have a few questions:
1) Since...
Hello,
I'm flashing custom code onto a nRF52840 based PCB.
I'm using SDK v14.2, SES 4.52.
The board was running fine for a couple of days.
Suddenly when I reflashed...
Hi,
I started coding form ble_app_uart, and whenever I set a breakpoint and it's caught, then I press Resume (eclipse), the code falls on NRF_BREAKPOINT_COND in app_error_fault_handler...
Hi
My English is not very good, but I encountered a problem that could not be solved. Please forgive me if there is any improper expression in grammar.
When SPI sending...
1.Development board used is nrf9160DK，sim car is nb-lot,set's network mode is nb mode，Turn off all peripherals
2.set eDRX mode,eDRX is 655.36s,pwt is 2.56s ,After the device...
I am using the GPIOTE driver to attach interrupts to a pin in a very timing critical environment (using sensors like this ).
To me, it seems like there is quite the significant...
In the v16.0.0 SDK the settings struct size is 904 bytes, but in the nrfutil it's 803 (screenshots attached). I figured the settings in python don't include peer_data(64bytes...
I was in the process of integrating a NAND flash to my project. - MX35LFxGE4AB
Initially, I thought it would be good idea to use QSPI, but it seems to only support NOR flash...
Hi
Im struggling to use the ble_app_template_cpp within SDKv16. I am using the nrf52840 DK (PCA10056) and want to us the S140 SoftDevice. The example isn't built for either...
Hello everyone:
The problem is still not resolved
Test broad is PCA10056
Test code was modified by \SDK17.0\examples\peripheral\usbd_msc\pca10056\blank\ses
Try to...
I am using a thingy52 device and in that, added code of advertising and scanning from the sdk 16. Advertising is run successfully. But getting packet loss issue. So, I am...
Hi
Im developing an application that will wake up on RTC every 15 minutes. My issue is that when using idle_state_handle, which in turn calls sd_ble_app_wait, the RTC...
Hi,
Trying to figure out the current requirement on GPIO input, can you point me in the correct direction in how to figure out how much input current the GPIO on nrf9160...
