I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
SDK15.3
SES
nRF52840
Hello Folks,
I'm trying to reduce my applications power consumption further in system off mode. For testing my IO configuration and System...
I am trying to build one of the Thread examples.
nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b\examples\thread\simple_coap_client\pca10056
Keil uVusion V5.15
When...
Hi everyone,
my problem is pretty simple: we developed a custom board for the NRF52840 to work using a custom protocol or BLE. A few sensors are connected to the NRF using...
Hi,
I am using NCS v1.1.0 and modem fw 1.1.0.
We had prepared our application in NCS v1.0.0 and now i have moved it to v1.1.0.
In new sdk v1.1.0 ,When i try to get Address...
Hello , I am advertising from a nrf device with advertising interval of 40ms. and I want to measure this interval at scanning side.
How I can measure using timer , timer...
I am using nRF52 DK to evaluate the TX power settings using sd_ble_gap_tx_power_set command:
sd_ble_gap_tx_power_set ( BLE_GAP_TX_POWER_ROLE_CONN , m_conn_handle, tx_power...
I have a project that needs to scan and filter the advertising name, uuid and mac address from the device. I will set them one by one and enable them one by one. I set them...
My problem seems to be a lot like case numbers 217967 and 243215.
I do not have an oscilloscope or logic analyzer.
I am using a nRF52840 DK (PCA10056 1.0.0 2018-17) and...
I've just received my nRF9160 development kit this morning and after trying to setup the development environment for a few hours I've come to a halt.
I got it working...
I am looking to use libuarte in our project. We are creating a battery powered device and so need to be low powered. EasyDMA draws about 1mA when running which is far too...
Hello,
We are developing an application that is trying to receive a steady stream of bytes from a serial port. But we constantly get a fatal error when we call app_uart_get...
I'm running 6 X Thingy:91s in pre-production for use as a GPS tracking/iOT solution. Currently I'm located in Austin, TX. If I do not request GPS, I receive regular data from...
Hi all, I'm working with NRF52DK using Segger Embedded Studio with NRF SDK 15.0 trying to communicate to a UART sensor using the serial port abstraction layer API. Following...
