Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Development Software: SDK v15.3, IDE IAR v7.8, SoftDevice 6.1.1
Computer Platform: Windows
HW revisions: EYSHJNZWZ (nRF52832)
Hi,
My application requires SPI and...
Hello Team,
i am evaluating Custom software Codec inside nrf52840. need development help whether it supports custom codec or not? which bluetooth stack used for development...
I'm working on a NRF52832 project with SDK V15.2, using S132 Softdevice. before connecting, nrf_fstorage_write/nrf_fstorage_erase/sd_flash_write/sd_flash_page_erase all are...
Hi.
I am using SDK15.0.0.
I tested the RF communication through the ESB example.
And I have tested the BLE communication using the ble_app_hids_keyboard example. ...
Hello all
currently I am flashing the device using command line:
#erase chip nrfjprog --family NRF52 --recover #program softdevice nrfjprog --family NRF52 --program...
Hello,
I'm trying to read an ADC value from a sensor(for POC I'll be using a pot wired to 3.3V VDD and GND) but all the examples I found only demonstrated reading the internal...
Hi,
What is your recommended stand-off for your aQFN package to PCB?
Below image is from x-section after mounting nRF52840 to PCB, these are aQFN pads, could you advise...
Working with NRF5 SDK 15.0.x, if I configure an GPIO as output, its initial state is low. I can set it high after configuration, but it is briefly low. Is there anyway to...
Hello to everyonel.
I am working with the Light_switch example of Mesh 3.1 on nRF52832 (PCA10040). At this moment, I am trying to understand how I can send a message from...
Hello!
I want meashure pulse time via input capture.
I configured NRF_P0, NRF_GPIOTE, NRF_PPI and NRF_TIMER1.
It work fine, but in datasheet I found next text: ...
Working with NRF5 SDK 15.0.x, if I configure an GPIO as output, its initial state is low. I can set it high after configuration, but it is briefly low. Is there anyway to...
Hello,
I've got an nRF52832 embedded in a module (Telit RE866). As such, I can't see the markings on the chip and have to resort to reading the FICR registers to identify...
