I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Because I encountered the same problem, so I needed help. I ran the nordic official example E:\sdk\nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a\examples\ble_central\ble_app_multilink_central...
I have successfully used the guide for BLE DFU.
But now I have trouble using the DFU via serial port. Do you have a guide for serial DFU?
I have tried two things.
...
I have a weird question:
On the nRF DKs (51&52) there are pin headers to connect them to an Arduino.
When delivered, on these headers there are some sort of plastic clamps...
As I working on a new project I am writing the code to support the new SDK driver structure and not including any "legacy" code support.
This highlights the fact that the...
I have a custom board with nrf51422-QFAC, used with SD 130 and SDK 12.3.0. My firmware consist of ble_app_hids_keyboard example modified. Schematics are attached below.
...
Hi all,
I using 1 Provisioner provisioning for some Nodes (light switch server) . If I have 5 Nodes in mesh network
I want to remove Node 4 from network and then add it...
I am working on a BLE peripheral (nRF52832 & SDK 15) which uses the Peer Manager to handle encryption and bonding to a previously existing central device. Sometimes bonding...
I am using the Segger Embeded studio and wondering about the SWO output.
I know I can load code and set break points with just SWDIO and SWDCLK.
So with RTT do I really...
HI all,
I'm working on the nrf52840, and I've tested this on the devkit as well as on-board on the product I'm working on. Using the saadc, if I tie my AIN line to VCC...
My use case initially is a single central sensor server powered from the mians and serving by BLE one battery-powered peripheral that has one of the commonly available st7565...
Hi,
MacOS serial device name is changings all the time when the nrf52 DK Eval board is re-powered. Meanwhile I have /dev/tty.usbmodem49, counting up. Next time I re-power...
We want to be able to download a firmware image into external flash through multiple paths (wireless or wired -only one path is used at a time) then program that image into...
Macbook pro mid-2014
High Sierra 10.13.5
I get the following message when trying to select the PCA10028 on the serial port:
2018-07-06T22:53:49.427Z INFO Application...
