I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
I have created a device that will connect and pair with one central. I would like it to re-connect automatically after disconnecting because it was out of range or turned...
I can connect/pair/bond to the nrfConnect app and disconnect then reconnect just fine. When I try to do the same to a central running on arm bluez 5.43, the second and subsequent...
I am getting a SOFTDEVICE: ASSERTION FAILED after some time when advertising with whitelist. I am using NRF5_SDK 14.2.0 and have tried both softdevice s132 5.0.0 and 5.1.0...
Hi,
I am trying to use the fstorage lib in SDK 12.3.0. My code is based on this example: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5...
I'm sampling from the SAADC with a microphone attached and need to send the sampled data over ble to devices, and I want the devices to recognize the data as being a audio...
I need to develop a beacon application with the OTA DFU capabilities (Buttonless). I have the NRF51-DK.
As a starting point, I tried the bootloader example located in the...
Hi,
I'm designing a pcb for nrf52832, and acc. to specification sheet (2nd para under fig. 98) i need to use differential mode to avoid ground bouncing. Can I share a pin...
Hi DevZone,
I am going to implement Arduino CAN bus shield on nrf52840 preview DK. I am wondering if I can use the Arduino CAN bus library in the nrf52840 preview DK. As...
I'm using sdk 14.2 and I have nrf52832 board. Now when I go to armgcc folder in sdk of any example (I'm using the blinky example ) and open my command prompt and try to build...
Hello,
In SDK14.2, select an armgcc project, for example, pin_change_int.
For nRF52840, the heapsize is defined in /components/toolchain/gcc/gcc_startup_nrf52840.S,...
Hi,
I've compiled the pc-ble-driver-py library on a raspberry pi but it doesn't come with a "make install" command. Could someone help me get the right file structure so...
Hi,
I am looking library for EINK Epaper display. The display I am using is https://www.waveshare.com/wiki/1.54inch_e-Paper_Module
Can I get library code for this?
I have issue while building the nrf5 bluetooth mesh light switch example using CMake on windows for Eclipse. I have run the following cmake command:
cmake -G"Eclipse CDT4...
Using SDK 14.0.0 with an nRF52832, I'm trying to use the data length extension, following some sample code found in this post:
https://devzone.nordicsemi.com/f/nordic-q...
