hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
Hello,
I want to connect one board trough SPI to my nRF51-DK. Using SDK11 and SD130, the nRF51-DK is the SPI master, I call the function nrf_drv_spi_transfer() but the...
Hi ,
In my project , i can use the battery service in my project.
But if i want to use the another four ADC channels , how to add it ?
my project is working at SDK 9...
Hi,
I am using 2 nRF52832, one for ESB Tx and one for ESB Rx used to send payload through UART using SDK11.
Tx board is used has a low power transmitter which transmit...
hi all,
i am a begineer to nordic. i want to send data over ble and read that using master control pannel.
please say wat api i want to use and how to use. please give detail...
Hello I'm new of nRF seriese.
nRF51822CEAAD00(0x004d)
SD130 ver2.0.1
kail Ver5.18
SDK11.0.0
I just finished the tutorial and now I'm making my new project with twi...
Hi, I am using Heart Rate rate monitor code to send floating value instead of unit16_t.
I am using the heart rate service to send the data. Instead of using simulated sensor...
Hi,
I am new to nRF5x BLE devices.
I need to create a project and would like you to help me out.
I need to connect two nRF51822 devices. If one of the devices goes...
hi dear officers
since the datasheet states that value 1 stand for connected, does it mean this pin is active-low.
in order to physically reset the device, could i connect...
I have tried ble_app_uart_c project in SDk 9 , SDK 10 or SDK11 , but they have the same problem.
Problem is that slave(SDk 9,ble_app_uart) can send data to master(by terminal...
While trying to bond an iPhone 6 (running nRF MCP App) with an nRF52 with S132 2.0.0 I encountered the following error:
On the first try, when the iPhone is not yet paired...
I am trying to set up a button interrupt by adding the following functions:
void button_interrupt_handler(nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_gpio_pin_toggle...
Dear Sir,
When nRF51822 is a slave, it should be updated software through Master(Z-Wave CPU) remotely.
How can we update SoftDevice software in nRF51822? UART, SPI, or...
My code detects an external signal using GPIOTE. Whenever the signal falls, GPIOTE calls a handler, audio_stimulus_handler . The code is shown below. Essentially, after detecting...
I have a nrf51-dk. I would like to the pincode to be stored in some configuration settings which is written in non-volatile memory. I do not want the pincode to be hard-coded...
