The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
We have some legacy code ported from other platfrom to nRF51822.
The old platform supports blocking flash write, so there will be some
readback code after flash write function...
I've had good luck running the examples such as the blinky and the basic BLE examples. Now, I'm trying to get the SPI Master example to run, but it does not seem to work out...
Hello Everyone,
As mentioned in nRF51-DK user guide, nRF51-DK has segger J-link debug out functionality. that means we can use this on board segger for downloading hex...
I have the nRF51822-DK and have been able to build and run the sample projects, e.g, ble_app_beacon.
I've just built a board using Taiyo Yuden's EYSFCNZXX module that's...
test the gpiote_example for timer0 in pca10003, the function is ok, LED blinking 200ms. but I change the timer0 to timer1 or timer2, the LED always on,and never blinking....
Hi! I use S130 on nRF51822 device.
After device is connected as peripheral I try to discover services using Master Control Panel but device disconnects. In Master Control...
I'm trying to start advertisement after establishing peripheral connection (on BLE_GAP_EVT_CONNECTED event) but called function sd_ble_gap_adv_start(...) returns NRF_ERROR_INVALID_STATE...
Hi
I'm working on a project to drive a DC motor, I really didn't find any example. I would like to know how can I program a pin in Keil, and I would be happy to have a...
Hello,
I am trying to get a lower connection interval from iOS. But the lowest connection interval I could get were 30ms.
Anyone has experience to achieve the connection...
Hi.
I find this code github.com/.../nrf51-dfu-single-bank-ble
I want to compile bootloader and download it on PCA10004.
I have KEIL 5.12 and the project file of the link...
Hi,
I want to create a service for test logger. Through this service i want to write n bytes at a time and after few delay want to write again some n bytes. These written...
I'm struggling to get started using Keil with an NRF51822 mounted on a custom board that I have cobbled together.
I have opened the blinky/pca10031 example as a starting...
Hello, I have two nRF24L01 devices that can already talk to each other on a custom address. When I try to talk to the nRF51822 from one of the nRF24L01 devices, I cannot get...
