I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
I have a nRF51822 Evaluation kit I am trying to get up and running. My kit has the older QFAACA part.
I followed the steps to setup eclipse and GCC and i am successfully...
Hello,
I took the ble_app_hrs rebuilt it and used Control to verify all is correct. I also tested it with the nRFTools Android App and it works fine I see temperature changing...
Hello,
I am currently starting with the hole ble topic. This forum helps me a lot in the last weeks to understand ble.
I am using S110 to provide a peripheral device...
I use the nRF51422 with S310 stack and i found the nRF51422 power consumption are quite different after connection on different phones which run the Master Control Panel as...
I have written some code that uses the SPIS to transmit data. One of the bursts is constant, for example I have a fixed sequence to send using the SPIS and so if I define...
Hello.
I use nrf51822 EK and custom board.
I have to replace the bd address i can not be found in the ble_app_ibeacon_bcs source code.
Is it any way to fix the bd address...
Hi. I'm curious if there's a way to filter devices in the "Discovered Devices" list while scanning with MCP. We have a lot of BLE devices in our office, so the list is fairly...
Hello, I am looking for the way I can use PWM to control duty cycle of connection. I am really novice and my understanding about programming and Bluetooth protocol is really...
I'd like to use the pin sense function as the power switch of my NRF51822 device. That is to say, after the very first power cycle (reset or battery change), the device goes...
Hi everyone,
I am trying to learn nrf51822 using Keil,
I need a very simple program to learn such as:
function bluetoothhandle(value)
{
if(value=="test1")
{
bluetooth_write...
Hi,
I tried to combine BLE HRS & UART together on nrf51822. The service initialization code is
void advertising_init(void)
{
uint32_t err_code;
ble_advdata_t advdata;...
Hi,
I am trying to get the PWM example ( github.com/.../nrf51-pwm-library) to work with a Softdevice (S110) that advertises.
There have been several Questions on the...
hi hakon, you told me to do " Try using the variable, for instance by setting "rx_info.rssi = rx_info.rssi;" in the callback and see if that helps." in the question i have...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
