Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
Hello I currently have an error when flashing with j-link on a custom board. The mcu is nRF52833 QDAA and the debugger pin is connected to 4 pins. In VSCODE, CONNECTD DEVICES...
I am working on a pdm microphone INMP621. I am getting the pdm data using nrfx pdm drivers but not sure about the logic which I am implementing to convert pdm to pcm. I read...
Hi, I need a little help with mcuboot.
We want to transfer firmware updates via CAN (MCP2515), which is already implemented. Was we are short of time, and we want to integrate...
We have a design using a nrf5340 with a Renesas Wifi chip, That Renesas chip uses a 1 wire interface for Coexistence
We are using Zephyr 3.5.0 and have tried to follow https...
Hi, I have Adafruit I2S MEMS Microphone Breakout - SPH0645LM4H for getting sound and for driving output via speaker I have tas2x63EVM amplifier. Since the nrf5340 audio dk...
Hi,
We want to have some RF-PHY tests on nRF52840 DK.
Therefore, I need a HEX file to make nRF52840 DK get into direct test mode and communicate with CMW270 with UART...
Hi,
I am currently testing the HID Keyboard example in SDK17.1.0. When the nRF52832 is connected to the computer and the Caps Lock key is toggled, it prompts "CAPS ON" or...
I tried to install nRF Sniffer. I followed the instructions here: https://docs.nordicsemi.com/bundle/nrfutil/page/nrfutil-ble-sniffer/guides/installing_nrf_sniffer.html I...
SDK: NCS v2.6.0
Program Software: v2.6.0\nrf\samples\openthread\cli
Hardware：nrf52840dk_nrf52840 and third-party module(nrf52840 soc)
The program runs normally on...
I am writing to seek assistance regarding an issue I am encountering with the SPI0 interface in the NRF52840 module. The project requires the use of four SPI interfaces, but...
while trying to package my hex file from zephyr and I have gotten the following error
nrfutil pkg generate --hw-version 52 --sd-req=0x00 \
--application build/zephyr/zephyr...
I've been playing around with the MQTT example for the nrf7002dk and noticed that the mqtt_helper_publish function used from the MQTT Helper libraries doesn't handle acknowledgements...
Can someone please, for the love of all that is holy, point me towards some guidance on how to read values of custom characteristics set by another device?
I cannot find...
Hi,
My fw running on nRF52840 (ncs2.4.0, zephyr) develops from HRS sample application. It acts as a peripheral.
In this project, I have a dedicated thread to receiving...
Hi, this should be a straightforward question, I am writing some code to randomly generate a number, and it works fine the only issue is I don't know how to limit the range...
