It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hello,
I am implementing the periodic search for lte managment (using SDK 2.5.2 on a nrf9160).
The periodic configurations in struct lte_lc_periodic_search_cfg is: ...
In the Wi-Fi Fundamentals Course, Lesson 2, Exercise 2 (step 7.2) I found that it is necessary to clear the bssid parameter in the wifi_connect_req_params structure. If it...
Message:
Hi Nordic Semiconductor Dev Zone,
I am developing a PCB that mirrors the one in Sony WF-1000XM5 earbuds, but with the microcontroller replaced by the nRF9161...
I use NRF52832 as a Bluetooth gateway to receive commands and initiate connections to devices. Each instruction received will be interrupted through the IO pin, and the MAC...
HI Nordicsemi Team,
I am exploring how LE audio works, as far as I understand a supported mobile can be connected to nRF5340 and stream audio from mobile phone. However...
Hello!
I am currently running into throughput problems while using the Nordic Uart Service (NUS).
I am building a project for a peripheral and wanted to test the possible...
With nRF as advertising peripheral, is it possible to measure RSSI of active scanners' SCAN_REQ packets. `bt_le_ext_adv_cb` has a `scanned` callback, but it looks like it...
Hi,
I am using the nPM1300 in combination with a STM32L431KBU MCU.
Also the code from Nordic to communicate with the nPM1300: https://github.com/NordicSemiconductor/npmx...
OS: Window11
Programmer version : v4.4.0
Used Chip: nRF5340
Used Hex file: peripheral_uart_nrf5340dk.hex
An error occurred while Erase&Write the Hex file while testing...
The default setting for the external flash chip of 9160dk appears to be 64m, but when used, the log display only shows 8m, and only the part within 8m can be used,
Then...
Hello,
I am trying to use PWM to control two LEDS, one red and one green (referred to as blueled in the code) to produce different colours. I have had a look at the example...
Hello,
When we flash the BLE Zephyr project to the external chip (nRF52833), do we need to add the SoftDevice controller .hex file as well, or does the merged .hex file...
I am trying to send / receive bi-directional audio between two nRF5340 Audio DKs with an external I2S bus on the gateway DK. I am modifying the nrf5340_audio example from...
Hi,
I'm working with nRF5340 and would like to store my own data in the NVM (2 bytes in total).
I couldn't figure out which flash partition is relevant for this and what...
Hi,
I just started developing a BLE Central device on a nRF52840 DK. After successfully connect my DevKit with a phone acting as a peripheral (using nRF Connect Mobile)...