Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
Hi everyone, I am attempting to measure I2S rate against internal clock frequency since I am using APLL. I am following examples in NRF5340_Audio application. What i have...
Currently, I'm using the NRF5340 chip. In my own development board, I'm only powering the chip to test its transmission performance. The example program I'm using is the classic...
nRF52840 using Zephyr 2.0.0
We currently have a system that after we are running can drop to 20uA. However, on boot, we draw something like 5-7mA. This large on boot current...
I work on a project with nRF52833 ( NRF Connect v3.0.2 currently) and I have to use an external AT45DB641E flash chip connected over SPI .
The external flash will be mainly...
example: ncs/v3.0.1/find my/pair before use I want to implement the ptx and prx of the ESB in the find my example "pair before use". That is, how do I operate when both BLE...
In our application we need a PPS signal even when LTE is enabled (and GNSS is disabled). The GNSS API gives some encouraging PPS info, stating " GNSS only starts giving pulses...
The current specifications (v0.8) for the nRF54L series of parts provide very little information about the input impedance of the SAADC peripheral. There are no values specified...
We are currently facing a troublesome issue: we need to send 242-byte data packets at a fixed 3ms interval. We connected an LED light after the data transmission module to...
Dear Nordic Support Team,
I hope this email finds you well.
I am writing to seek your assistance with a build issue I have encountered while using the nRF Connect SDK...
Hello,
I have already implement the RSSI2 monitoring where I get the RSSI2 value with each successfully received packet via pcd-callback and its attached nrf_modem_dect_phy_pdc_event...
The app can work well in nrf52810 QFN48,it can't work as design in QFN32.
I have created my module with nrf52810 QFN32, loaded softdevice,loaded app,enter debug mode with...
I'm still new to this but particularly in regards to battery. I have a custom board with a nrf5340 and have been working on reading the voltage. I used the battery sample...
Hello,
I am building my own board with the nRF9151. I see that it can do SPI, but it does not say what pins are SPI capable. As the chip is a SoC (or CiP), can I use any...
