Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
What is the difference between the Async Read ApI and the Normal Read API of the ADC ?How the ASYNC read API work ,can anybody explain with sample code. Specially thirds argument...
Hi, We have designed a custom board using nRF52840 SoC, now we want to calculate its power consumption I want to ask if we can measure custom board power consumption using...
I am trying to use the NRF52832 to connect to the BMA456 Accelerometer from Bosch using SPI and am running into the following issue:
All read/write commands work fine...
Hi, I'm trying to implement a timer that will trigger each 10ms (for example) an handler function and do something inside it. So, I came with the idea to implement an App...
Hello !
I would like to use pin P0.12 as common gpio output and configure it on quite later phase in my SW.
I use nrf_gpio_cfg_output and set/clear for have relevant value...
Hi,
I'm working on central_uart and peripheral_uart examples. I want to get the rssi value and tx_power of all advertising packets from peripheral to central via bluetooth...
Hello Everybody,
If you're reading this, you're likely in the same boat as me and need to scale Nordic's build process in an environment that doesn't have access to west...
Dear, We are working on a project where we have to request and read out data from multiple (up to 50, but can split up to 8 per central device) BLE modules (BK3432_QFN32)...
Hi!
I am totally new with Segger, so this is an idiot's question:
When I open a sample project and want to check my settings using the
"Configure nRF connect SDK Project...
I can't seem to be able to activate the iBasis sim card.
I'm in Norway.
It gets passed the initial screen and says the it needs user data. It then pre-populates with the...
SDK Environment: nRF Connect SDK v1.8.0 Target: Decawave DWM1001-DEV. This uses the nRF52832
My application uses more than half the flash size of the nRF52832.
Using mcuboot...
Hi, I'm working on nRF9160 modem firmware update.
For Understanding SPM with secure and non-secure firmaware, I have used UARTE2(secure peripheral) into non-secure firmware...
Hi All,
I am trying to run two UARTS using LIBUARTE.
this is the relevant configuration:
#define NRF_LIBUARTE_ASYNC_WITH_APP_TIMER 1 #define NRF_LIBUARTE_DRV_UARTE0...
Hi Everyone,
sdk : nrf Connect v1.7.0
ide : VS code
I was trying out central_hr sample on nrf52840 dk. I have simulated hrs server in nrf Connect mobile application...
