Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
I'm seeing an assertion failure at PC=0xa806 in nrf52840 + S140 7.3.0, while using L2CAP.
I know the most common cause for softdevice assertion failures is interrupt/timing...
Hi, I'm using nRF52805 and SEGGER. My BLE device disconnects with the mobile app occasionally. The disconnection happens randomly. In the debug mode, I see some messages....
hi,guys
I have a product that uses CHIP 52832qfaae0, and then I replaced chip 52832qfaae1, and there is A problem. Chip 52832qfaae0 runs normally with the same code, but...
Hello,
looking at the compatibility matrix for the 820 it seems that rev2 of the 820 can be used with softdevices and the legacy SDK v17, while rev3 can only be used with...
Dear Members,
I want to use SPI LCD and Sdcard, they have different CS, but sharing the same SPI ports, I have used different SPI instance but not giving us a good response...
On opening a sample project located at https://www.nordicsemi.com/Products/Development-software/nRF5-SDK with keil V5 , I can directly have an error message “Cannot read RTE...
Hi there, I'd like to make some FIR or IIR filter on my nRF52840 DK. I guess I'm supposed to: 1) Provide .a file into SES project's tree (or as Additional Input File): 2)...
I am working on OTA update .
Right now i am working simple
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v5.0.0%2Fmd_doc_user_guide_modules_dfu_configuring_performing...
Hi,
Is there any command for reading the type of Nordic SoCs (e.g, nRF52833 or nRF52840) that is going to be programmed by nrfjprog/ J-Link Commander?
Thank you!
Hi Nordic,
I want to write a value from the application layer to the bootloader flash region through uart, and use this value to replace the button 4's function of entering...
Hi All,
I'm using buttonless DFU for upgrading the firmware and my requirement is I would like to know the time taken for complete DFU from my application.
One approach...
Hi, I am working on designing specifications for a new product, which will potentially be using the NRF9160 as the main processor, since the main application is centered around...
Dear Nordic support,
We are trying to know the current consumption during BLE RX & TX. However, there appears to be apparently conflicting information. Which is right...
