We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi
I am interesting to generate 1,638,400 Hz is an external clock for a peripheral on one of the NRF pins.
Please advise how can I generate this clock value on one of...
To the kind attention of Nordic support team,
We have this custom board using nRF52833 powered up from usb and in high voltage mode (ldo). The problem is that we are...
VS Code (running on Ubuntu 21.10) can't find the connected nRF52840 dev kit. " Could not find any connected boards " is all that's shown under CONNECTED DEVICES. Beside that...
I'm learning to use the Asset Tracker V2 example and planning to build a POC product on top the example. The biggest issue at the moment is with power consumption. On the...
To the kind attention of Nordic support team,
We have a problem that may very well be linked to this thread
https://devzone.nordicsemi.com/f/nordic-q-a/65202/usbregstatus...
Hi, I got my border router working fine, but I do not understand its use. How can I connect (which kind of protocol?) with the nrf5340 from my laptop to send turn on a led...
Hello
We check the current in system off in PCA10059 board. and use the ble_app_template application.
If set the VDD 3.3V, after the system off, measure the current is...
Hi Team,
I want to connect power pins on the nrf52840 chip in the schematic.
I find there several VDD pins, how can I select and connect them?
Best,
Gaosheng
Hello,
we are currently developing a customer product based on the nRF9160 SIP.
The requirement is to send the battery voltage periodically over the CoAP protocol (PUT...
Greetings , I have implemented an application with freertos (sdk 15.3) which goes into low power and wakes up on two irqs (rtc and button). When the button irq arrive turns...
We would like to use nRF9160 has MODEM only feature, such that MCU in our product can talk to nRF9160 via UART interface.
We have found an sample application [Serial LTE...
Hi
I am trying to setup a raspberry pi 4 for flashing nrf devices. But Nrfjprog doesn't seem to work.
I am using a Raspberry Pi 4 with 2021-05-07-raspios-buster-armhf...
Hi,
I noticed that the nRF9160s I2C low level logic voltage is quite high. With a 2kR resistor at 3.3V it's already more than 200mV. Because this is quite high and will...
