Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
Hi.
I have got an Iphone 12 and installed nRF Connect. I cannot see the MAC address of connected device. That was possible on my old Android phone.
Does anyone know why...
Hi,
I am using nrf9160 to communicate with LIS2DHTR.
I use I2C_2
In file nrf9160dk_nrf9160_common.dts in ncs\v1.4.0\zephyr\boards\arm\nrf9160dk_nrf9160
&i2c2 ...
Hi there,
I'm using MacOS Catalina 10.15.6 and nRF52840-DK (2019.9) for the Sniffer. My PCB is running BLE on nRF52840. The hex file used for the sniffer is sniffer_nrf52840dk_nrf52840_7cc811f...
Is there a Hardware Design Guidelines white paper for the nRF52840? I'm looking for something similar to what is available for the nRF9160. For example, this:
https://infocenter...
when I used simulator in keil5 for NRF51 software debug, there is a problem : *** error 65: access violation at 0xFFFFFFF4 : no 'write' permission. When I used the keil5 command...
Hi,
I am using nrf52840 DK and SDK version 17.0.2. I want to write data into particular address location(application area) of the flash using fstorage. It is writing the...
Hello ,
On NRF52840 DK my logger works fine and I get no problem with printf(). However, on my custom board the program goes into hard fault with the following :
0x4001...
Hi there,
I'm using nrf52840 DK and Custom board, SDK 15.1.0, Segger Embedded Studio(SES v5.20)
my issue is when i receive data from uart interrupt based on serial uartes...
Hello Guys,
I'm developping and st7789 IPS screen driver and i'm having problem with SPI0 . I'm using NRF52840 DK 2.0.1
First I took SPI example from sdk 17.0.2 configured...
Hello All,
I am using SES on BMD340 controller with FreeRTOS project.
After few modification in the code, I am facing *.elf doesn't exist during linking stage. There...
On a nRF52833 on a custom PCB, due to space and allocation limitations, I need to run UART Rx and UART Tx over GPIO pins that are limited to standard drive, low frequency...
Dear all,
I have a NRF52832 module (EBYTE E73) and before yesterday, everything was fine.
We had a outdoor test last week and till then, everything was fine.
After...
I've tried this with both 1.5.0 and 1.5.1, with the same results. I install the SDKs using the toolchain manager, and when the installation finishes I open a bash shell, also...
I'm learning how to use OTA DFU on Win10 laptop. I followed this and this guide step by step. I have a couple of questions:
1) (See below code) How to use " arm-none-eabi...
