Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
Hi,
I'm working with the nrf/samples/nrf9160/at_client (@ tag v0.3.0) with a PCA10090 board.
I had a question about the response to the AT+CESQ command.
Specifically...
hi,
i am quite new with programming tools like the nordic thingy and i am currently trying to get some initial program running, i.e. the blinky example. i have a few questions...
I am converting the simple_on_off vendor model to send a message on mesh 3.1.
the server implemented the simple_on_off model successfully. But but my client runs into 0...
Hi currently I am using the nrf_mesh_sdk_3.1 latest release light_switch Example both client and server one after successful compilation and load examples in DK boards when...
Hello,
I have updated secure_boot to allow UART3 to be used in the non_secure area. However, as soon as I try to initialize it in the non_secure area a hard failure occurs...
Hello! I took the example of "usbd_cdc_acm" and added a receive and transmit buffer. The data from the receive buffer is sent back. It turned out that the first byte is written...
Hi All.
I have a project where my peripheral (nRF52832) connects to my central (nRF52840), and then transmits 128 byte packets continuously one after the other. It works...
We are using the nRF9160 DK with the Asset tracker example, which is working in combination with the nRF Cloud.
Now we want to use our own AWS account in combination with...
hi all i am trying to read data from a sensor in burst mode i can"t able to read all datas from the register .I tried to read the data in both spi and spim(with easydma) ...
Hello,
So I'm using nrf52832 with sdk15.2 and I'm trying to connect a joystick to the adc pins and have the joystick to move the mouse instead of the buttons and having...
hi.........
i am tried to merge the blinky and timer sample program , i am getting this error , even i have included all files .h , .c files
nrfx_config.h: No such file...
Hi
I am using nrf51822 chip to develop my application & I need to put the hardware into sleep. In which all the gpios & other peripheral goes stop to save power.
SO, how...
Hi,
I want to change MAC address during advertising in nrf52810.
nrf52810 receives MAC address via uart from other MCU and set this MAC address. (type is BLE_GAP_ADDR_TYPE_PUBLIC...
We're building small robots/toys that work with each other.
Would it be possible to use the nfct on two devices with nRF52840 to communicate between each other?
Also...
Hello,
I’m sorry for asking again, but I could need some help again. This is a followup to devzone.nordicsemi.com/.../missing-endcrypt-event.
I’ve managed to receive...
