If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
Hello,
I have a problem with Indicate Characteristic. When I try to send data using sd_ble_gatts_hvx() function, it always sends 20bytes from address 0x00. This is my code...
I am trying to run my program once per second using timer. The timer is initialized as follows:
APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_MAX_TIMERS, APP_TIMER_OP_QUEUE_SIZE...
I'm trying to figure out how the bonding works in the multilink demo. It seems like the central device only goes through the bonding if the peripheral has the multilink service...
ble_app_uart_s110_pca10028_nuevo.uvprojx
Hi, I´m using a nRF51244 with s110. I program it in nRFgo Studio (s110_nrf51_8.0.0_softdevice.hex)
I try turn on the passkey...
Hi,
I performed an OTA update of my APP. (SD 7.0 and BLE single bank bootloader were flashed).
The update finished without an error and then my application even starts,...
Hi,
I'm developing on a custom nrf51822-based board, and using the s110 softdevice, version 7.0.0. With JLinkGDBServer and the toolchain's gdb, I can debug softdevice-less...
Do you have a BLE SOC chip that can behave as a master and a slave, and also has embedded stack so no host processor is needed. I am looking for a chip that can be used in...
hi,
Inorder to flash the softdevice to evaluation board PCA10024 , i tried using nrfgo studio as mentioned in the user guide.but the nrfgo studio does not show any board...
Dear all,
I am using SDK7.1 with S130 v0.5 alpha. Can I use the DFU example in the SDK6.1 to update my firmware in the chip(nRF51422)? If not, is there any alternative...
I am using S110-based peripheral device which is sending 20byte notifications. Application on my peripheral works fine (testing with MCP gives transfer rate about 15kB/s which...
Hi,
I was using nRF51DK with Keil uVision ver 5.14 and SDK 8.0.0. It worked okay yesterday and I tried HW peripheral as well as BLE peripheral.
But today it doesn't...
Is it possible to identify a device as a previously bonded peer based on the advertisement package and before establishing a connection?
I would like to be able to bond...
Hi
Im using nrf51822 board from RedbearLab. SDK6.1and SD7.1.0.
I added DFU to my application and iam able to update the firmware OTA.
My issue is after adding dfu...
Hey there,
I am looking for the right pin out to wire up a reset button to my board so that I can reset the IOS device is paired to. Can some one help?
Tyler
