Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
Features
nRF52840
nRF52832
System current consumption DC/DC at 3 V
0.5μA at 3V System OFF mode,
no RAM retention
1.5μA System ON mode, no RAM retention...
Hi
I'm running the blinky sample (modified) on a custom board based on nrf9160. When compiling with SDK2.3 and toolchain 2.3 the current consumption is about 84uA (LED off...
Hi,
I use VS code (windows 10) to program nRF9160DK under modem mfw_nrf9160_1.3.6, application Asset Tracker V2, JITP certificate generated by nRF Cloud and good SIM card...
What is the power consumption to check battery level?
How quickly at boot time is an accurate battery state of charge available?
What is the RDSon in the path from VBUS...
Hi,
I need to read the registers of the KTD2026 IC as specified in the datasheet.
In short I have to send a read command with the device address (0x30), the address...
Hi, I'm working on a BLE peripheral project using nRF52840 with nRF5SDK version 17.0.2 and softdevice S140 version 7.2.0
We are considering to increase our full device name...
We are starting a new design that requires a LTE-M chip. Upon comparing features between nRF9160 and nRF9161, I see 2 differences
DECT NR+
3GPP Release 14
First...
Hi,
I am reading through different Nordic documentation. In some documentation, it shows a first stage B0 Nordic bootloader. This bootloader then can point to MCUboot...
HI,
I have a product which scan for RFID card through NFC and Mobile Device through BLE after nRF52840 MCU was wakeup.
If I scan NFC and BLE scanning separately, everything...
Working with a Pinnacle 100 using an NRF52840. I have a HMI with a TTL serial interface. I have verified I/O on the HMI itself via a TTL/USB converter to Tera term, but having...
Hi! I have a fleet of narrowband and cat-m devices around the world. I want to determine their rough position by using the cell tower information. I tried CellLocate from...
I have a board with the nRF52832 and a board with 12 SK6812 LEDs on it in the shape of a ring. I have code that sometimes will display the correct color on the ring but other...
I think the NFC pin is set to the default state on the nRF52832.
Currently, I set CONFIG_NFCT_PINS_AS_GPIOS to 1 to use it as a GPIO pin, but is there a way to make it the...
Hi, I'm using nrf52810 ,nrf connect, zephyr, vscode extension. I’m having trouble using both UART0 and the NUS UART service. Here’s a snippet from my overlay file:
/ ...
