Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
I have recently upgraded my SDK from NCS V2.2.0 to V2.6.0, and have come back to some firmware I had working under 2.2.0 as I need to progress that. The firmware is based...
Hello,
I just got started with the nRF5340 DK. I went through the example which instructs how to load the "Blinky" applications, build it, and then flash it to the Board...
You may ask what poolside means. It means at my community pool, where I don't have Internet access via Wi-Fi for my laptop.
I wish to run some AT commands like AT%NCELLMEAS...
Hi, I have followed the instructions in Securely generating credentials for nRF91 Series devices - nRF Cloud but cannot connect to nRF Cloud.
I think the instructions on...
I'm confused about the use of these two functions. I want my app to sleep immediately upon start and then wake up and do a BLE advertise when I press a button.
I...
Hello everyone,
I've been spending a lot of time to fix the issue not being able to enter DFU mode with the following error. I've changed so many versions of GCC, but it...
Dear Nordic devzone community,
I have designed a custom board using nRF9160 and I am able to send and read out certain AT commands which confirms to me that most of the...
I'm transitioning from SES to Visual Studio Code.
In SES, I can define multiple builds and then define preprocessor options (eg. -DOPTION1) for each build definition
I...
Hi there,
We are quite new to Zephyr. We are currently porting our existing app onto Zephyr as a test. We are currently using NCS 2.5.1
So for our existing application...
I needed to add my own partition to the primary flash, and was able to do so successfully by adding a section to the device tree partitions.
However, when adding MCUBoot...
Hi,
I'm trying to setup my NFR52840 DK to act as a NFC tag so that I can read some simple data on my phone via NFC transfer.
I have tried a few NFC sample applications...
Hi,
I am using a modified HTTPS Client demo code [Let's say Version A] and sometimes when trying to debug with Segger Embedded Studio for ARM (Nordic Edition v 5.34a/Jlink...
Hello,
From time to time I am getting the error " Unable to find bootable image" when I start a debug session in SES-NE v5.60.
FIH_CALL(boot_go, fih_rc, &rsp); if (fih_not_eq...
I am trying to read the GPIO state on an nRF52840 right after it wakes up from deep sleep (System OFF mode). I have configured 4 pins as wake-up sources from deep sleep System...
I have been working on finding the cause to an unexpectedly high power power consumption in several newly produced units of our product based on nRF5340. I believe I have...