Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Good day,
I am developing app by SDK 17.1.0, including ble_nus and ble_hid, I would like to imply fuction to switch between ble_nus and ble_hid, due to some difference configuration...
Hi!
I am trying to subscribe to the power management events that correspond to the following log lines (which I can clearly see in the log):
I have been trying with this...
Hello All,
I'm currently now on the initial phase of development and i wanna to stream 2xIMU data through SPI as for now if i connect only one IMU as Follow
P1.15 SCL...
Dear all and Nordic Staff:
I am learning about dynamic multiprotocols and found examples of dynamic multiprotocols for Thread and BLE in the "nRF5 SDK for Thread and Zigbee...
Due to the system design of our products, I am going to need to sideload any firmware update binaries. That is, my application code will handle receiving the update through...
Hi
I am using ncs v2.3.0, mesh chat example
I have used CONFIG_BT_CTLR_TX_PWR_PLUS_8 =y , and it works quiet well, now how can i implement CODED_PHY (long range) in this...
Hello,
I came across a Nordic Q&A discussing a sample called hci_uart_with_usb_uart_bridge in this post . I have searched in the v1.0.1 tag but couldn't find the mentioned...
Hello,
I'm attempting to establish communication between an nRF52840 and an nRF9160 on the nRF9160DK using LPUART. Initially, I tried using the interrupt-driven mode, but...
I get the registration "parse_cereg: LTE mode not found, error code: -22" error,when try to connect to LTE network in china shenzhen.the hardware is custom use nrf9160 chip...
sdk 2.1.0
nRF9160
Hi, I need to parse a JSON file and for that I'm trying to use zephyr's json.h library. Based on the automatic test file I built a piece of code for...
Hi,
I am trying to use an ST7789 display with the NRF9161DK, I was following this guide but got no luck:
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b...
Hi,
I was looking into hooking up an SD card to the nRF9160DK that I use for data collection during evaluation and early stage pilot projects. I noticed that there is an...
Hello,
I am trying to use a membrane keypad that has 5 buttons. It's not a matrix keyboard so I was just going to add 5 buttons into whatever gpio pins I can spare, but...
Hi,
I'm trying to use the samples/subsys/modbus/rtu_server/ sample. We use the st3485eb as rs485 driver. The problem is that I don't receive any data.
I'm converting our...
Hello DevZone,
I'm testing the nPM1300 with the battery inside the Thingy:52, which has rated capacity 1440mAh and rated voltage 3.7V.
The charge current is 800mA.
I...