Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
We are using both serial ports running over USB on the nRF54L15DK:
uart20 is LOG, CONSOLE, etc.
uart30 is for our communication (enabled in our overlay)
When we...
Hello,
I am trying to get a custom board working with NOR Flash chip but I am having issues getting the flash chip "ready". I am running the sample application "spi-flash...
Hi!
I've used nrfutil to dfu ble before on a target that just loads and runs a bootloader (for cycle testing).
I'm trying to use it again with a target in the application...
We have a NCS 3.0.2 app + MCU boot with OTA functionality on nRF54L15 (PCA10156 rev 0.9.3)
After upgrading to NCS 3.1.1 it doesn't boot anymore.
I tried with
Key provisioning...
nRF9151 has access port protection enabled by default. I need to debug firmware for nRF9151 produced by a non-secure build. I am trying to follow Figure 120 (Access port unlocking...
Hello,
I have a series of nRF52840 devices that are already connected together in a Thread Network.
My system is composed by one client and multiple servers.
My devices...
Is there any way to filter for verified answers/closed tickets? Seems like it would be really useful for helping people find answers and answer posts which have none.
Greetings,
Using SDK v3.1.1 I've configured 3 PWM outputs using the pwm0-2 modules via a DTS overlay. After reset or power cycle (and prior to making any PWM driver calls...
After cancelling a flash operation to my nrf7002DK (PCA10143 1.0.2), I'm unable to flash my discovery kit again. I have tried both the regular west flash for our application...
Hi,
I use flash read operations at the BLE interrupts, because I need some of the stored informations. However, while I am doing another flash operations and BLE interrupt...
Greetings,
What's the maximum clock rate supported by the SPI1 interface on an nRF52840? My DTS overlay indicates it should use 32MHZ for one device and 8MHz for the other...
I am tried to access the server using http_client .I am tested that my implementation to access the local server works properly but the thing is i am tried to access the ...
I am looking for the datasheet for the nRF31512. I am looking to see what the pinout for this chip is. It is not for any new project as I know it is old and discontinued....
Hi,
1. Does the P1.02 (NFC port) on the nRF54L15 support PWM? 2. If it does, please provide the overlay configuration method and sample code.
Best regards,
Peter.Mi...
Hello,
I am building an example app that uses MbedTLS and non-offloaded sockets, because offloaded ones do not fit my needs - updating security credentials needs disabling...
