hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
I'm developing a device that occasionally bursts large data payloads (~30kB) over BLE. It uses MPSL to share the radio between BLE and ANT+, so I'd like the BLE radio to use...
In the documentation , it is stated:
The SAADC is preceded by a gain stage which has a programmable gain. The voltage range seen at the input of the gain stage is:
...
Hi:
I'm doing the exercise L3-E1.
I used nRF Connect SDK Toolchain v2.7.0 because it didn't work with v2.8.0
How do I make NRF Terminal appear?
Thanks and Best...
Hi
nRF54L15-DK QFAAC0, ncs v3.4.0, project path: ncs\v3.4.0\zephyr\samples\boards\nordic\system_off
After compiling and flashing this example, the power-on reset (POR...
Hi Nordic,
I am uing DECT NR + on NRF9151 and trying to do some kind of network discovery like knowing how many devices available in the area. As far as I can do with the...
Hi,
In the NRF54LM20A Development Kit, in addition to the tank circuit (L5 + C8) in the path between DECA and DECRF, there is also a filter made from C7=2.2uF and FB2...
Hello Nordic Team,
I am working with an nRF52840 on a custom hardware board and investigating the current consumption in idle condition.
I have tested the same hardware...
I’m using NRF Connect SDK 3.2.4 with the nRF54L15-DK. I’ve successfully used the nrfx_gppi_conn_alloc() and nrfx_gppi_conn_enable() APIs to connect a timer to a GPIOTE output...
Hi,
I have a custom PCB with an nRF54L15 with custom PCB trace NFC antenna working currently with ncs v2.9.1. The NFC is used for commissioning and reading out parameters...
Hello everyone! We were working with our nRF52DK boards and one of our students had issues flashing a board. He used a recent version of Segger J-Link Commander (V9.30 as...
HW: nRF54L15DK
Phone: Pixel 10Pro Android 17
When trying to use nRF tools to test channel sounding i am only able to get the infreqent mode to work, both normal and frequent...
Hi,
From this old thread, nRF Sniffer seems can decrypt the mesh packet.
But I still failed with add network key, application key, device key and IV index.
I attach...
Hello, I am developing in a Zephry environment on the NRF5340 and am looking to enable APPROTECT and ERASEPROTECT on our NRF5340 MCUs. We want to enable a recovery key so...
