I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hello. I am trying to change the UUID value of a service and characteristic of my nRF52 to have a custom value. I have successfully done this in firmware and it has been found...
Hello everybody,
I am currently working on a project in which I need to read some data from a glucometer. Until last week it was working fine, however I stopped receiving...
Hello,
I installed nRF Connect SDK V2.0.0 using "NRF connect for Desktop"
Now I can't open nRF Connect SDK projects on segger embedded studio.
It showing only VS Code...
Hi,
I'm trying to get a better understanding what causes some unexpected current peaks while nRF9160 is in RRC-IDLE with the NB-IoT mode. I have been experimenting with...
Hi,
I have installed the nRF Connect SDK v2.0.0 with Visual Studio and can now successfully, build, flash and run the nrf9160 at_client sample application. But when I try...
Hi,
I am trying to run any of the samples, even the most basic ones as blinky, and they will not run on my nRF52840 dongle, which has a header to program directly with jlink...
Hi,
I have installed the nRF Connect SDK v2.0.0 with Visual Studio and can now successfully, build, flash and run the nrf9160 at_client sample application. But when I try...
Hi,
I have installed the nRF Connect SDK v2.0.0 with Visual Studio and can now successfully, build, flash and run the nrf9160 at_client sample application. But when I try...
Hi,
I have installed the nRF Connect SDK v2.0.0 with Visual Studio and can now successfully, build, flash and run the nrf9160 at_client sample application. But when I try...
Hi,
I am trying to run the sample code for the BME680 sensor over I2C.
I am using the sample code as is; the only modification is my overlay file to define the I2C pins...
ERROR: JLinkARM DLL load failed. Try again. If it keeps failing, please ERROR: reinstall latest JLinkARM from Segger webpage.
I tried downloading three different versions...
I need to read a SPI device every fixed milliseconds so I thought to create a TIMER and read SPI slave inside its handler. But there are some problems cause I get all zero...
Please provide me the sample code for TWIM using the nrfx_twim.h
I want to create the TWI master using the nrfx_twim.h
Please provide the sample code for same.
Hello Nordic team and fellow developers, I am working on an adafruit nrf52840 feather sense board, for which i have created a custom DTS file. I am trying to interface with...
