Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello, I will start by saying that I am using an M1-based Mac for this. I believe I have loaded the correct x86 versions of things (like JLINK). I have nRFConnect 3.10.0 desktop...
Hi,
I have a nrf52840-DK board connected to an upstream nrf52840-DK board as well as another downstream nrf52840-DK board.
This setup will run fine for a couple of hours...
Hello, I'm working with the event manager doing a customized Asset Tracking version firmware. The problem is that when I attempt to submit an event with an array with fixed...
Hi,
In my system I have a timer that ticks at 1kHz frequency, collects some data and sends it over BLE via bt_nus_send. It works fine, but in the beginning of the stream...
I want to incoorperate the pc-ble-driver into a product, using the PCA10059 USB-dongle. My design requires me to receive advertising scan responses. I successfully receive...
Hi,
I'm using nRF Connect SDK 1.7.1 with nRF52833dk.
I'd like to implement DFU over UART.
I see a number of examples to achieve this with SDK5, but not with nRF Connect...
Hi,
I would like to know how much noise I have to expect with the SAADC.
I tried the example "saadc_pca10036" and attached the pin P0.02 (AIN0) to a ground pin on the...
Hi,
I have a project with 3 threads running on a nRF9160. I am using nRF Connect SDK v1.8.0. Basically I borrowed the code from "mqtt_simple", "location" and "threads"....
Hi all,
I am working on a project which needs dwm1001 library integration with nrf52 ble code. I am using ble_app_uart code. decawave have provided dwm.o and libdwm.a...
I have an issue compiling the example code from SDK 17.1.0 using Microsoft Visual Studio Code in Windows 10. Using the easiest example possible, after starting a terminal...
Hi Nordic,
I'm able to do dfu without validation after few days of studying documentations and forum.
Here is the settings page i'm flashing:
But i had to disable...
Hello all,
the sensor is selected and so far powered via an external power supply, while the nrf52dk is powered via the USB, however, I am not sure how to properly organize...
Dear ,
I am using the nRF52833-DK development board with the NCS1.7.0 SDK.
Recently I just found that when clicking the flash option in the vscode, the IDE only builds...
Hi,
I'm using the saadc and I notice that the max value that saadc can convert is 3,3V. If I try to convert an higher value, the result has no sense. For my project, I need...
Currently I am working on a open thread project.
Right now I am facing an issue in which my board/code is getting reset every time after I have done some changes in my previous...
