hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hi, I'm doing experiments with Bluetooth direction finding. I am using the example of the nRF52833 development board, and I have obtained the IQ representation of CTE and...
Hi I am using the aws_iot example on the nrf9160 DK.
I have opened the zephyr.dts file and in the section uart0: it has the following
I've reached this point trying...
Hi,
I am looking to connect the ds18b20 sensor to the nrf9160dk. I followed this post, but when I tried running it, I was getting a "create_nordic_project.py failed (1)...
2022-04-12
Hello Devzone Community,
I have a couple questions regarding availability of nRF9160 LTE modem settings PSM and eDRX. Question (1) If my local celular carrier...
Hi,
I have opened a ticket with Kenneth and verified it by mistake. It is now locked. I have done the changes Kenneth asked me but it didn't resolve my problem.
thanks...
Hi,
I am connecting my nrf9160 based system to the nRF Cloud and sending data from it.
I got the cloud to show the RSRP values that I sent it through the following JSON...
NCS 1.8.0
Modem FW 1.3.1
For other products I've worked on with cellular modems, we would add in back-offs to the firmware in the case we failed to open a PPP session...
Hi,
I've been playing around with the attached low power mode example. It seems to be written around the nRF SDK, but I am attempting to build and flash from within VSC...
Hi Team,
We are working with nRF52832 and nRF Connect SDK v1.8.0. Our application needs to sleep (power save mode) for 5 minutes and every 5 minutes it should wake-up...
Fota used to work fine in SDK v1.7
No I have moved to SDK v1.8.0
I don't believe my software has changed, however I am getting an error when running as follows:
Any...
Dear Nordic Engineers
Our customer use nRF9160 to develop a tracker.They found that their programs were relatively power-hungry.They tested the serial_lte_modem example...
Hi there!
I am trying to combine the SPI and ble_app_uart examples.
However, when I add the SPI part to the uart, it shows this:
I believe there is some problem...
In the demo in test \ v1.9.0\zephyr\samples\subsys\usb\audio\headphones_microphone , I found that only dual channel 16bit 48Khz audio can be recognized on the PC. the product...
