Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
According to the way our production and the way we update the firmware.
I will need a bootloader for nrf5340, so I can update the firmware via SPI.
What will be the best...
Hi,
Currently, I'm working with the ISP2053, one of the nRF5340's 3rd models.
As a beginning, my colleague wrote a code based on the throughput sample and I found...
Hi iam using nrf52840 dk board and for programming i use keil software ,the issue is i could not program the dk board and it is a brand new board. When I try to program it...
Hi guys! I'm a beginner of nRF52832, and I met an issue as the topic said.
When I init the UART module, it will cause an "APP_UART_COMMUNICATION_ERROR", and the error code...
Note: this question was previously a reply on my other question, but I accidentally marked it as an answer so the thread got locked. I have now deleted that reply and am posting...
Dear All,
could you explain the function of TP8 and TP9 of the nRF9160 DK on HW 1.0.0 ? These test points are connected to pin 124 and 125 of the nRF9160 which are marked...
I am using nrf9160 custom board with an external flash memory mx25l6433f. I first tested the external flash with the example 'sdk-zephyr/samples/drivers/spi_flash_at45' and...
Hi,
I;m working on nrf52840 dk i have to enable ble5.0 long range.
i set the tx power 8.
according to my project my device will be always in advertising mode and my...
I am trying to scan for BLE devices in my area, but when I connect to the USB840XZ with the windows development tool the "Start Scan" button is not active. There are some...
Hi everyone,
is there a way to update the AWS certificates from certificates.h with the SDK 1.9.99? Following the AWS FOTA instructions it seems that i can update the certificates...
Hello everyone,
I am currently testing the secure bootloader over USB example but I am currently facing an issue when I start a DFU.
Here is my configuration:
...
Hi,
Application details:
I have a datalogger application that samples data every second. It uses the following modules:
TWIM0 -> To communicate with external RTC clock...
Hello,
I am working on application using nrf52810 SDK version nRF5_SDK_14.2.0_17b948a.
Here my application sends 240 bytes of data every 150 ms. But after sending few...
Hi,
I use the a gpiote_in_event to trigger a number of PWM pulses which works fine so far. However, the exact behaviour of the generated signal is important so that the...
