hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hi,
I'm looking for some guidance.
I'm using a HolyIoT nRF54L15 dev kit to evaluate their nRF54L15 module.
I am currently looking power consumption.
I have tried the...
I'm wanting to repetitively read the SPI buffer as a master to check a status bit. I figure there's no sense in using the DMA when I can read the SPI RXD buffer directly....
Hi
I am trying to use the two GPIO pins. One GPIO pin is configured as a input and connected externally to a button.
The second is configured as an output pin. I want...
I am trying to complete the course "nRF Connect SDK Fundamentals" using a nRF52840 DK board (version 3.0.0) connected to a Mac Mini (Intel processor) running macOS version...
Hello,
I'm experiencing high current consumption with Zephyr OS. I'm using SDK 3.1.0 and the device still draws about 900 µA, and I don't know why. Although I have a custom...
Hi all, I am going through the beginner course and am using the MPU-6050 over I2C. I am able to communicate with the board where I get the WHO_AM_I. I can also read from the...
Hi,
I am getting framing error notifications from the nrfx uarte driver on a zephyr platform when receiving data from a certain external device, but only when there are...
Hello,
I want to have 2 applications running on nrf5340 CPUAPP (nothing on CPUNET) with app1 in flash and app2 (in RAM) getting launched by app1 once placed in RAM as a...
After switching to the BLE advertising module in SDK 16.0.0 (on an nRF52 board) and using it for over 3 months I am now discovering that no matter how I configure the advertising...
My firmware is blocked on custom board until RTT connects: Code hits and blocks on a printf. This doesnt happen when using an NRF5340, but does with NRF5280. Just trying to...
Hello, I am using v3.1.0 of the nRF SDK with a nRF52840-DK board.
I would like to run the "Counter RTC Driver Sample" (nrf/samples/zephyr/drivers/counter/alarm). The README...
I am updating our production tools and starting by simply trying to program the Thingy91 (or DK) with the following example from the internet. I keep getting timeout errors...
Hi Team,
I have configured I2C0 for reading data and sending iqs323 and iqs7211a. i have configured overlay file according pin conjuration which is below.
Pin configuration...
