Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
What is the tolerance of the internal ADC 0.6V reference voltage for NRF52840?
i.e. what's the max/min of the 0.6V reference or what's it in percentage?
Where can this...
Hello,
Windows10 X64 VS Code,nRF5340-DK;
when i change NCS1.8.0 hello_word to NCS1.9.0,got error
it can build complete,but can't flash to chip.
i've remove build,and...
Hello,
I would like to know the number on ms that a timer has been running before stopping in a breakpoint while debugging.
I can know the number of ticks with the...
Hi, I want to enable Bluetooth support on nrf5340 for FOTA. Serial seems to work fine but BT doesn't seem to advertise.
I get the following error after flashing smp_svr...
I have two custom images that I flash to my chip (nRF52832, SDK v16.0.0, SEGGER Embedded Studio). Application 1 is located at 0x26000 Application 2 is located at 0x45000....
I am new to embedded f/w development. I would like to be able to debug zephyr projects. Can anyone recommend a debug probe to use with the nRF5340? and any debugger software...
Are there any other SDK options for nRF5340 than nRF Connect SDK (and Zephyr)?
The chip would be nice, hardware-wise, to a project, but the nRF Connect SDK looks like a...
I am having a similar issue to the person in this post where the wake from deep sleep on an interrupt sometimes works and sometimes doesn't. But for me, it's very consistent...
Hello,
I know this question has been asked a lot. But I haven't found one that matches exactly. I'm trying to flash a custom PCB with an nrf52832. I'm using the on board...
Hi,
I am trying to get a simple LED blinking using a timer, gpiote and the ppi. So the Idea is:
Timer compare event -- PPI --> gpio toggle. I am using the nRF connect...
HI,
I am developing an application which requires BLE connection. I am concerned about the energy consumed by the device during the connection.
I understand that once...
Hello,
I'm just starting to use Asset Tracker V2 from v1.9.1 and it appears that it is missing some device info such as version, carrier and other on the Device Information...
Hello,
I'm trying to send a custom reliable message between two nRF52840 DKs, using the nRF5 SDK for Mesh v5.0.0 and nRF5 SDK 17.1.0, by modifying the light_switch examples...
