Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hello,
I have been developing some products over the nRF51822 BLE. Got my introduction with nRF about 2 months back and despite the steep learning curve I was able to integrate...
Hi all. I'm using an old macbook and nRF Connect for Desktop just stuck at splash screen. Any version > 3.9.0 do not work.
System Version: macOS 10.13.6 (17G14042) Kernel...
Hello, I am using board nRF9160-dk (sdk 1.8.0). I need to get geolocation data using AGPS, for this I use the following sequence of AT commands:
AT%XSYSTEMMODE=1,0,1,0 AT...
I am currently working with the nRF52 DK and have compiled some code to read ADC values. This code works fine with the nRF52 DK but I am having trouble getting it to work...
Hello everyone, I'm developing a wearable device based on nRF52832 which reads IMU (ICM20948) data using TWI.
The problem is that if I try to use the code with a custom...
hello everyone,
in my project i need to advertise the sensor data as well as connecting the BLE TAG . in detail i am using nrf52810 with mpu6050 and i want read the accelerometer...
Hello,
During my evaluation of nRF52840 I discovered an issue which prevents the device from joining a Zigbee network successfully.
I'm using out of the box zigbee/light_bulb...
Hi,
I've installed all by the book watching the installation videos and I have a problem building in VScode
when I try to build with nrf connect app window I get this...
Hello,
To preface, this project was redirected to me and I have very little experience using SoCs. Happy to provide any additional information and apologies for issues in...
Hi!,
I am trying to create an application with BT Mesh using the nrF52840 DK and two nrF52840 Dongles with an OnOff Model Server and an OnOff Model Client respectively....
Hello.
I am new to Zephyr, I know how to digital read the pin which is used as INPUT
#define SW0_NODE DT_ALIAS (sw0)
static const struct gpio_dt_spec DOUTINPUT = GPIO_DT_SPEC_GET_OR...
Greetings,
I'm using NRF52840 with softdevice and nRF5_SDK_17.1.0 on NRF52 DK.
The shutdown_handler in my code is as follows:
There is a secure bootloader from Nordic...
Hi, I am using nRF52832 module as connectivity chip (GAP peripheral, GATT server) with ble_app_uart_pca10040_s112 as source.
I am using nRF connect app to test data communication...
I am currently developing a feature for a BLE module to pass certifications (BL654 Laird, based on nRF52840). My application runs on SDK 15.0.0. I used the "radio_test" module...
