I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
The discussion in https://devzone.nordicsemi.com/f/nordic-q-a/79364/maximum-number-of-bytes-that-can-be-used-in-beacon-advertising suggests that we should be able to populate...
As far as I understand I should be able to use the nrfutil (6.1.x) on a Rpi 4B to update any of the nordic semi devices nrf5x supporting bluetooth (i my case nrf5340) Will...
I am new on Bluetooth. Currently I am playing with BL5340 development board. I need a firmware to test Bluetooth data transmission latency between two BL5340 modules. Could...
Hello,
I'm running the Asset Tracker V2 NCS 1.7.0 conected to the nRF Cloud. I'm using a Thingy:91 with external GPS antenna.
The GPS position is being correctly aquired...
Hello ,I am starting new development in Nordic environment and my system configuration is intel i3 with 8gb ram.
Still it is way too much slow to open nrf connect for desktop...
Hello everyone,
i want to use the 52810 to write into a SD -card, i use a slightly modified fatfs example.
The problem is, the SD card will not initialize as the p_event...
Hi, I'm trying to implement a sleep mechanism in my app. I based my code on the Power Management Example.
I use a button to put the app to sleep and the same button to wake...
Hi Team,
I am working on a project. It requires nordic chips (slaves) to communicate with msp430 (master). I use the nordic example SPIS as the initial code of the nordic...
My project consists of STM32 + 4G + nrf52833. When the 52833 firmware needs to be updated, the cloud service will send the 52833 firmware to STM32, and then STM32 will send...
Hello all!
I am currently developing on the development board nRF52832, SDK16.0 and SD132v7.2.0.
My developmnet board acts as a central whereas my phone as peripheral...
Dear team,
1. I am using the Ble_app_uart example from the SDK.
2. I had received the data successfully from the nrf_connect app.
3. Once the data was received over...
I received my nRF52840-DK (PCA10056) last week and today I was given the task to get started.
I started setup my environment with my preferred choice: Arduino IDE. Unfortunately...
Hi
In the actual test, the power consumption of the chip when scanning is started is 9.5mA,This actual test value is higher than the Iradio_rx0 and Is1 in the PS .What is...
Hi
The customer wants to test the RF transmit power of the nrf9160，whether the AT command can be fixed frequency?Or whether there are special tools to test RF power?
Hi,
I'm trying to migrate bluetooth softdevice to a project contained cli module. I found cli module and softdevice would all create an app timer. The softdevice first created...
