hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hi everybody. I'm trying to design a mesh network in which most of the nodes, if not every, should be a relay due to parallel positioning of the devices and each one of them...
I am working on Windows, using NRF Connect SDK 1.5.0 (have also tried the SDK 1.5.0r-rc1, with an updated nrf_802154_serialization module to be able to compile).
I am using...
Hello, I have run into this problem again with regards to using the lwm2m_client sample. I can start running it fine but I get the error "Cannot init lwm2m engine" and "Cannot...
when compiling "ble_app_multirole_lesc_s140_pca10056" of sdk nRF5_SDK_17.0.2, crypto library not getting included, I am getting error, library is placed as shown in pic, also...
Hello,
I know that you can generate a single zip that contains dat and bin files for sd+bl and dat and bin files for the app.
Is it possible to generate a single dat and...
HI, I'm new here, hope following the rules for Questions.
I'm using nRF Connect v.3.6.1 and as toolchain SEGGER Embedded Studio for ARM (Segger edition) V5.34a.
I need...
Hello there,
I am using nRF52840 PDK and nRF5_SDK_for_Thread_and_Zigbee_v1.0.0 SDK for BLE and Thread development. I also have a BLE smartphone app communicating with nRF52840...
Hi,
-I have a custom board using nrf 52832 and I have interfaced LIS2DH12 using an SPI interface. -I am using SDK 15.2.0. -I am collecting raw data using FIFO mode and send...
I want to realize audio playing function in 9160, according to the specification, there are 9160 I2S interface. However, the specification only describe the definition of...
I am testing UART example using nrf52 DK(nrf52832), SDK17.0.2. (\examples\ble_peripheral\ble_app_uart\pca10040\s132) Setting UART initialization to a specific pin will halt...
I use ANCS example from SDK 15. But I found that I'm not able to get more than 32 chars for ATTRIBUTES (BLE_ANCS_ATTR_DATA_MAX). And it's a little short to get Title, Sub...
Hello,
in our application we have one central (nRF52840DK) and up to four peripherals (nRF52832). We want to achieve two goals in this application:
Goal 1: We need a synchronized...
Hello I have built a custom board using an nrf52810 chip and have been trying to upload some examples from the nrf52SDK (specifically BLE examples with the s112 SoftDevice...
