hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hello,
I'm new in the Nordic sphere and I'm starting in embedded programming. I was confronted with the following problem and I will try to give as many details as possible...
Hi,
got a question about UART and maximum bytes it can receive in one burst or "packet".
Using nRF52382 and SDK16.
Recently I've been developing a new app in which UART...
Hi Nordic Team/public users,
Request your assistance for troubleshooting the NDK-nrf52840 board that was having a detection issue whereby my laptop/PC was unable to detect...
Hello, I hope you are safe and well during these times. I have created a successful prototype using the Adafruit Feather nRF52 Bluefruit and the Arduino IDE. I think I am...
Hi,
I want to update the DFU with application nRF Connect (Bluetooth) for beginning I want to try with nRF Example in example/dfu/bootloader_secure. The file secure_dfu_secure_dfu_ble_s130_pca10028_debug...
Hi,
I like to use nRFSDK in my future project, but I don't like the hectic steps to open a project when using nRFConnect SDK. I cannot open Segger IDE directly instead go...
Hi everyone,
Currently, i am working with some zigbee devices using NRF52833 and zigbee SDK 4.1. Now, i want to use BLE DFU with it to update the firmware when needed. ...
I am developing with NCS, but I found only one project "v1.4.99-dev1\nrf\samples\bluetooth\peripheral_lbs" I can add files directly through the option "Add new file to cmakelist...
I m using sdk16.0.0 nrf52-ble-app-uart-c-multilink example. I want to comminication arduino btw BT840F. I try with nrf52840 there is no problem but when i use bt840f i didn...
I'm using a library that does
#ifndef MIN
#define MIN stuff
#endif
Because I'm using segger, I have no control over compilation order, so that's getting loaded first...
I want to design the chip (nRF9160) on our board. 1- What kind of external debug / flash (SWD) can I use to flash the modem firmware and my app?
2- Is there any suitable...
Hello All,
I am implementing a simple UART bridge over BLE and want to add a Characteristic to update the baud rate being used. I thought I added code to support a new characteristic...
Hello!
I have this interesting bug with the twim driver.
It works perfectly with the NRFX_TWIM_XFER_TXRX transfer type: I see the transaction go out on the bus lines...
Hi,
My project uses nRF52840 with SD 140, SDK 17.0.2 and SES. My hardware has SD Card SPI and LCD SPI sharing bus pins, using CS pins to switch devices. Because of this...
