Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
I want to use the four peripherals UART0, UART2, UART3, and I2C_1 on nrf9160. When I was building the project, I encountered the following error.
Here my prj.conf
...
Hi,
I received a Thingy91 and am unable to commission it to nrFCloud.
The Thingy91 skipped orange breathing as mentioned in the manual here (step 4). It went directly...
Hi! I'm running a project with an nrf52 chip for which we use the JLink as the interface. I've been using my setup a lot for the past year. The other week, every LJink command...
Hello,
i'm trying to understand how the management of the SS pin is (or has to be) performed when using nrf9160 as SPI master.
In this post Håkon said that:
"Most driver...
Hi,
I using the radio test example on the pca10040 with nrf52832 EVB.
And set the radio test to Tx, the parameter as below:
Data rate: NRF_RADIO_MODE_BLE_1MBIT TX power...
I have searched the devzone and couldn't find any solution
followed the instructions from Nrf Connecta dn verified as well.. using
tag v1.1.0 (have done west update...
I'm using the MESH SDK 4.2.0 on a nrf52832 in combination with the Serialization interface (ACI) example
We'd like to implement the key-Refresh cycle and are planning on...
I am trying to setup (Nordic Edition) SES 5.10d for an example to download to the nRF52840 Dongle.
The tutorial* helpfully discusses how to avoid overwriting the MBR and...
I am using nRF52840-CKAA-R7 II2c to connect to my MSP430 i2c[ slave]. i have put any pullup on the clock and data thinking, to use nordic pull up in default. clock is connected...
Hello, all ..
I'm using nrf52 pca10040, s132..
I connected custom board and nrf52, and would like to communicate with uart. First of all, custom board is model cm1106...
I am looking to write my own IRQ handler for the UART. I read the post https://devzone.nordicsemi.com/f/nordic-q-a/46822/nvic-table/184731#184731
and added my own definition...
Hello,
I am new to Nordic and Segger. I am trying to build source code developed by a 3rd party. It was originally developed with GCC in Linux. I have followed some suggestions...
Hi,
I am working with nrf52840dk and using a peripheral _uart example from NCS v1.3.0. and the problem that I am currently having is that I cannot get it to low power. At...
