Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Using nrf5340dk, SDK v1.9.0
Want to add external RTC via I2C to wake mcu up via alarm, Facing Issue with I2C init.
I have gone through the suggested sdk fundamental course...
Hi,
When do you plan to update your Online Power Profiler Tool for cellular with nRF9151 device?
I just can see nRF9160 available for calculation.
Regards,
Hello,
I am working on an ESB (Enhanced ShockBurst) communication setup using the following hardware:
Receiver (RX): nRF5340
Transmitter (TX): nRF52840 MDK Dongle...
I would like to add smp ota firmware upgrade to the matter sample project, can you provide me with the specific steps to do so, and in which path is the ota file compiled...
Good night,
I installed the VS Code/nrf Connect in my Windows 11 Prof.
I copied the "blink sample" and I tried to build it, but I am receiving
* Executing task...
I am following this example https://github.com/crfosse/ncs_projects/tree/main/peripheral_zephyr , both secure and non secure and I am not being able of making the non secure...
Hi,
I am using Mesh of 30 nodes with avg Current Consumption 6mA and 2mA in sleep mode(by calling k_sleeps) , timer is 1s timer is running to keep Real Time incremented...
Hi. I used nRF Connect SDK v2.9.1 to add OTA to the Peripheral UART sample application. The target is nRF54L10, but when I build it, the flash usage exceeds 50%.
If the...
Hi
I see i get a cmake warning with DFU enabled with the following message:
whats the purpose of this? should i just have it always enabled in my conf, or for prod...
Since of the security issue, our 9160, are connecting to a private network (10.x.x.x) by the operator. While testing the FOTA function on this private network, the 9160 has...
Working with an nrf52805. Copied a simple example (peripheral_LBS) and found that RAM overflowed by ~2.2K I note that the nrf52dk_nrf52805 is not listed as a "compatible"...
Hi Team,
I am using nRF52840_DK to program my custom board but I am facing some voltage related issue from VDD pin.
Measuring on board it's giving 3.0V for VDD & GND but...
Hi
Two questions as below
1. About nPM1300 & nRF54L15 I2C connection, at nRF54L15 side, I put SCL/SDA at P1.x group, so INT also need at P1.x group? Or I can put at P0...
https://academy.nordicsemi.com/courses/bluetooth-low-energy-fundamentals/lessons/lesson-4-bluetooth-le-data-exchange/topic/blefund-lesson-4-exercise-3/
There are two "Section...
