Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hey guys, for testing purposes on nrf52833 and SDK 2.8.0 I want to use a simulation and stumbled upon bsim . I followed the instructions there and can build and run the hello...
I encounter this problem:
The radio_test application works correctly on the official nrf52840dk board, but cannot receive input commands on my custom product board.
However...
Hi,
I have been developing a PCB with an nRF9151 and a SKY65943-11 LNA among other ICs. I looked up the nRF9151 Development Kit (PCA10171) datasheet for some of the pinouts...
I am running a modified asset_tracker_v2 on a nRF9160. all is working fine. I am upgrading from SDK v2.5 to SDK 2.90. After a build I find the merged.hex file under the build...
Hi everyone,
I've purchased two nRF905 modules ( www.otronic.nl/.../nrf905se-draadloze-transceiver-met-antenne.html) . I want to establish communication between a Raspberry...
we used SDK V2.6.2,
we used external flash for the OTA,
when we do the OTA after the NVS flash is erase so how we can solve this,
we used nvs_storage for this,
EMPTY_0...
Hi.
After migration from SDK2.7.0 to SDK2.9.0 I have issues with power mangement. CONFIG_PM_DEVICE_RUNTIME=y, which I used, causes that twi driver doesn't start. I try to...
I am using a customized PCB (nrf52840) and I have been successfully set up the SPI communication in between the nrf and lsm6dso
I used 0.11 as clk , 0.27 as MISO and 0.25...
Hello. We are testing nrf5340 - nrf7002 using the example of blpovisioning. I try to put on/off function using button, but if I reset pcb and turn on, it will connect to wifi...
I have our app on the nRF7002-DK board running with MCUboot configured for USB firmware updates. That is working fine, but is there some way to enable the console output from...
Hello.
I have been successfully flashing the nrf52840 dongle using the nrfjprog comand. I have been successfully able to reset and erase as well. Recently however, none...
I'm facing issues with my brand new PPK2 tool What I've done so far, my setup : * Ubuntu, linux * I installed latest nrf connect application from official * Installed Power...
Hello,
I've been using nRF54L15-DK devboard (0.9.2 revision on the label) for about a month now without any problems until today.
I wanted to change VDD output voltage...
We are developing a system were we rely heavily on the use of LWM2M. Using the provided LWM2M client we normally dont experience any problems at all and are able to establish...
We're experiencing issues with RTT logging on an nRF9151-based project using NCS 2.9.0. When `CONFIG_LOG_DEFAULT_LEVEL` is set to `3`, RTT Viewer fails to connect to the device...
