I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
We have a board that is to be certified by a Chinese test lab, so I need to create an image based on the direct_test_mode sample.
In Zephyr v2.0.0 I created a custom board...
Hello,
We are using nRF Connect SDK 2.0 on an nRF52832 and were wondering if it is possible to use BLE and Shockburst simultaneously? If I compile enabling both Shockburst...
Hello,
A couple of days ago I run the examples direction_finding_connectionless_rx and tx on two nRF52833dk successfully, meaning that I could see the CTE info received...
Hello,
I have reconfigured the nrf_dm sample from ncs 2.0.0 to use Zephyr Bluetooth Controller by adding CONFIG_BT_LL_SW_SPLIT=y to proj.conf.
But then it's stuck in this...
i am using the uart0 on a nrf52840 to communicate with an quectel bg95 using async api (dma) on zephyr 3.1.
from the uart interface there are connected rxd, txd, rts and...
Hi,
I am attempting to merge two example programs together and have hit an issue with a hard fault when my timer interrupt triggers.
This works fine in the standalone...
I refer to https://github.com/alc6/nrf52-pc10040-multiperipheral-passkey/blob/master/main.c for implementing static passkey. But pm_sec_params_set() returns errCode=0x7. ...
What I've done
1) Set up ot-br on an Rpi4 by following this guide .
2) Set up a 52840Dongle (plugged into the RPi4) as RCP by following this guide .
3) Installed the...
I'm using SDK 14.2.0.
I'm trying to read the device ID register from ISM330DHCX accelerometer this way:
ret = nrf_drv_spi_transfer(&m_spi[Instance], ®_addr, 1, read_temp...
Hi guys,
So lately, I decided to update the sdk from 4.1.0 to 4.2.0 and there are some problem that I can not solve myself. So I use the macro ZB_ZCL_REGISTER_DEVICE_CB...
Hello,
i've trying to update the codebase of our current project (under development) from NCS 1.9.x to NCS 2.0.x.
I'm experiencing hard fault crashes when I try to perform...
Hello,
I'm using SDK 17.0.2 with S113, v7.2.0 on the NRF52840. We currently have an instance of CLI running in our executive loop, and it works fine. We'd also like to implement...
I facing the above issue when build a project. The project structure is below. I copied the Git project project to d:can/firmware/zephyr/samples/drivers/can from https://github...
