Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hi,
I used nRF52932QFAA ,SDK14.2 uart bootloader.it works well with softdevice loader 5.0.0.But when I download my app(without softdevice),it cannot work.
Flash composed...
Hi,
I am using nrf52832 custom board and sdk17.2.0.
My application is a Freertos application. I see that my application is going to hardfault from _start without entering...
Device: nRF5340PDK
So i have the same Problem as described here https://devzone.nordicsemi.com/f/nordic-q-a/74483/bluetooth-examples-are-in-infinity-loop, but i flashed...
Hi, I have enabled DFU in my custom ble_hid_keyboard in NCS v1.6.1
when i copy the same project and placed in another name after that build successful but while running...
Hi,
I have merged these two codes from SDK:
\nRF5_SDK_17.0.2_d674dde\examples\peripheral\timer
\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_beacon
I want...
Hi,
I have nRF52 dev boards (nRF52840) (PCA10056), I am using SoftDevice nRF5_SDK_17.0.2_d674dde.
I am not sure SoftDevice SDK 17.0.2 supports BLE 5.0 specification: ...
Hi I am using Ncs version 1.6.0 and nrf52840dk ..BT_HCI_LE_SCAN_FILTER_DUP_ENABLE this duplicate filter enable is not working in NCS.is there any workaround for that?
I have a question regarding the power sequence mentioned in the nRF52833-Dk guide:
or the power sources section the guide explains it as:
I drew the...
Hi,
I know that this question was asked before, but I can't find a complete/recent answer.
We are trying to use nrf52 DK board to perform bluetooth localization. In...
I have a few questions about the bootloader of the nRF52.
I used "nrfjprog --eraseall" to erase the chip, afterwards I turned the power off and on again while holding down...
Dear Community,
I implemented the beacon-example with S112 and 1MBit mode and with S140 and coded-phy 125k sending one beacon per second continuously at +0dBm (sd_ble_gap_tx_power_set...
I have attached a sensor board to the nRF5340DK board I'm using zephyr 1.6.0 on macOS
I ran an I2C scan example using I2C1 peripheral and it works fine
found 5 I2C slave...
Hello, I have an issue. When I disconnect device I need to know it's mac address. Can you answer, how do i can get mac address of disconnected device or list of mac addresses...
Hi everyone,
I'm working with the BMD-350 Evaluation Board based on the nRF52832 BLE SoC and currently using a customized version of the central ble_app_uart example from...
We have an existing product that uses a module containing NRF52832-CIAA
Due to supply issues we are looking to respin our board to use a different module that contains NRF52832...
When I reset the device and in some time connect it to JLinkRTTViewer, it shows only 11-12 first messages after the reset. Which parameter I should change to increase number...
