Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hi there!
I'm having an issue adding WiFi functionality to my project. I use the nRF9160DK and the nRF Connect SDK v1.5.1 on a Windows10 platform.
To keep it simple i...
I am using nrf52DK board as an observer to test my beacons. I have kept scanning enabled all the time (scanning interval & scanning window same), but the scan_evt_handler...
I want to use the nrf5x to develop the host/gateway of bluetooth mesh, may I ask which model is more suitable, which model currently supports the most mesh nodes?
And which...
Hi Nordic team,
I have successfully developed an application using nrfx (Timer/PPI/SAADC) combo in NCS 1.5.x to be able to sample 2x differential channels very fast.
Similar...
I have trouble developing BLE devices with Nordic NRF5280 and SDK 15.3.
I have a device that uses a custom BLE service, And when using nRF Connect on the mobile phone, all...
I have been developing some nrf52832 code (SDK 17.0.2) using the Segger RTT debug window for logging. I added the code from the UART example but the printf goes to the debug...
I'm planning to modify the nrf52832_ciaa reference designs in altium to emulate the functionality from a development kit and add an RTC.
I need access to pins P0.23, P0...
Hello. I would like to use an internal RTC to keep time going even if the power is off.
1. Is it possible to implement with 'nrf_calendar' module?
2. Should I think about...
I have a battery powered iOT device using BLE, I2C, and GPIO. I am focused on reducing the power consumption. When BLE is not connected, I want to have as little power usage...
This is in response to a central sending an update. I try and follow with the central's request except I set the times to the AUTO value. If I get an NRF_ERROR_NOT_SUPPORTED...
ran nordic blinky example on nrf52840 kit
Want to know where is the transmitter power set in the code.
refer any example where we can define transmit power
Hi Folks,
I am just asking general information (explanation and/or code samples examples) to set up a secured BLE connection between multiple centrals towards one peripheral...
Hi,
I'm programming a nRF52832 for SPI communication with another device which requires some single byte TX/RX. After a lot of head-banging, I realized that the nRF52 was...
Hello there,
if i download a hex-file to the NRF52840-Dongle with the J-Link (Lite) tool, the dongle always remains in bootloader mode (red led is flashing). But if i download...
