It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hello,
I want to run mass storage on my custom board with the nRF52833 and W25Q512JVEIQ. I have reviewed the mass storage sample (ncs\v2.7.0\zephyr\samples\subsys\usb\mass...
Hello,
I have a custom board with an nRF52833 and a W25Q512JVEIQ, which communicate over SPI (not QSPI). I successfully accessed the W25Q512JVEIQ (executed my own read and...
Hi, I am using nRF52832 module BL652. I want to measure the battery voltages of a 9V battery. What are the best possible resistors value to measure voltage of such battery...
Hello, We have a custom PCB with both the nRF9160 and nRF52832. Currently, the nRF52 functions as an HCI controller connected via LPUART to the nRF9160. We're at the stage...
Dear sir:
When I first use CHIP tool in my Ubuntu NB, I can commission bulb(52840) through OTBR(Pi4+52840 RCP) successfully, besides, I can use CHIP tool to control bulb...
Hello,
I am currently checking the RSSI measurement precision, and we got very large errors (up to 10dB error) on the RSSI vs input power.
To avoid any PCB / matching...
I'm new to nRF5340 development, and I'm reviewing partitioning for multi-image DFU. I've enabled the bootloader with CONFIG_BOOTLOADER_MCUBOOT=y , and after checking partitions...
Hey,
I am having an issue where my device doesn't show up in the Nrf Connect app as "connectable" despite as far as I can tell being set as a connectable device. This doesn...
Hello,
I'm trying to upload code to an external board using an NRF52dk, and am having an error in vscode as shown below.
My issue seems to be very similar to the one...
Hello.
I understand that Radio Notifications is an API that notifies you before and after scheduled radio events occur within a SoftDevice, but can you tell me more about...
Good day
I have the NRF_desktop keyboard application running on the NRF52840 Dongle, Zephyr 2.6.1. I would like to us the nrf52840 ProMicro as it has a battery charger build...
Hi,
I would like to know Number of UARTs available for Murata 2AB. According to the 2AB datasheet, there is one UART, but the nRF52340 datasheet shows two UARTs. Can 2AB...
While debugging the code with Nrf connect extension in VS code , code get stuck at the start only does not go any where getting the SIGNTRAP error continuous
HI,
I am building "esb_ptx" sample in NRF54L15-PDK, by using CONFIG_DYNAMIC_INTERRUPTS, but it;s always reset like below;How to config the prj.conf to enable CONFIG_DYNAMIC_INTERRUPTS...
Dear all:
I found that the nrf52840 flash size is only 1MB, but the size of light bulb load is about 850KB, I have some questions:
1. Does it contains the FOTA region...
