Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hi,
I used nRF52932QFAA ,SDK14.2 uart bootloader.it works well with softdevice loader 5.0.0.But when I download my app(without softdevice),it cannot work.
Flash composed...
Question - How to enter in DFU mode using open USB bootloader example on pca10056 ?
i tried writing nRF52840DK with examples-DFU-open_botloader-pca10056_usb and usb_debug...
hello,
I recently updated SES and got a new version of nrfSDK.
Secure_boot sample does not contain Cmake. In other SDKs on github secure_boot does not exist.
is...
What is the best way to filter info center results to match my project? I'm using SDK 1.5.1 for S132 and I think that is softdevice 6.0.0.
It would seem like a simple top...
We are currently running on mfw_nrf9160_1.0.1 and NRF master as of today (Sept 13, commit 224bee9).
We are developing an MQTT application that uses TLS mode sockets.
We...
52832 & s112 & sd6.0 & sdk15.0
If you have multiple pairings on the same host will return error by “pm_device_identities_list_set”
err_code = BLE_ERROR_GAP_DEVICE_IDENTITIES_DUPLICATE...
Hello everyone,
I trying my nrf52832 getting ultra low power current conception mode using System OFF mode (0.3uA). I using SDK 15.2 ble_app_beacon example I change 32KHZ...
I started developing on the Adafruit nRF52 module. I wanted to make a custom PCB to demonstrate a prototype and fabricated a board with a MDBT42Q module from Raytac. I sent...
Hello, I have used the nrf52840 . I have created applicaction from existing examples of SDK which used bluetooth. And now want to add OTA via bluetooth. Is it possible use...
Hi,
I am developing an app based on PCA10059 dongle. my program work fine on this dongle, but i have a problem with it. after programming PCA10059 dongle with my firmware...
Like the title,
Is it possible to disconnect ble link or stop advertising at runtime, then change the service uuid and characteristics?
I wanna to do OTA service in application...
I am able to receive motion data [rawdata] from thingy52 on my RPi 4 using bluepy library in Python3.
I want to extract the raw values of Gyro/Accl/Mag from sensor.
The...
Hi,
I'm writing a program that swaps between LTE and GPS to send the device's location to AWS over MQTT. I am able to connect to LTE and AWS, then swap to GPS and get a...
Hello. I 've got such problem with flashing some of the ESB protocol examples of NRF5 SDK. I use Adafruit Feather NRF52832 board with ST-LINK V2 debugger. https://www.adafruit...
I want to implement UART service which can act as central and peripheral at at time.
I am using nrf52832 board and sdk 15.
I tried to implement it by changing the services...
Hi,
I am following the nRF_Sniffer_UG_v2.2.pdf to setup the nrfSniffer. Wireshark does not show me my board among the interfaces. I had a look at the troubleshooting part...
