I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
I designed a circuit using the NRF54 to connect via Bluetooth and control several peripherals. I program the chip using the Debug Out of the NRF54L15 DK . The code can be...
Just bringing this to your attention. This has been an issue since at least 2.6.1, and appears to still be a problem in main.
static void connected(struct bt_conn...
Hi, What specific steps must be followed to modify the charging current (BCHGISET) of the nPM1304? The information I found says to disable the charger first (set BCHGENABLECLR...
I am evaluating the monitor mode debugging support in nRF Connect SDK with nRF52840-DK and an arbitrary BLE sample (like peripheral_uart). My SDK/toolchain version is 3.1...
Summary
We are running on an nRF54L15 and receiving continuous NMEA output from a GNSS module over UART using UART ASYNC. After some time (30 minutes to hours) of normal...
Hello,
I am getting an error with the modem_info_params_get() function when I try to get the modem parameters. I am currently using SDK 3.2.0 with the FW MFW_nRF9151-NTN_v1...
Board: nRF54L15-DK (PCA10156), hardware version 1.0.0 OS tested: Windows (Lenovo Legion 5), also tested on Linux — same result on both
Problem
The board is not recognized...
Hi, I am trying to sound two reflectors from a single initiator, and since the CS works on a one-to-one ACL system, I wanted to know how I can reset the CS-related stuff in...
Hello,
On my board I implemented an RS-485 interface using the ST4E1216IDT transceiver. The DE (Driver Enable) and RE (Receiver Enable) pins are tied together and connected...
Hi Nordic Team:
I am developing the firmware for nRF54H20 using NCS v3.2.0. I need to quickly configure 16 GPIOs as input with pull-up resistors, so I adopted the coding...
I want to highlight 2 infuriating bugs in nrf connect SDK. I believe it applies to all versions.
1) If you have more than one app in your applications tab, the context will...
Hi I would kindly ask what is the recommended layer stack up for npm1300 PMIC.
In reference designs 4 layer board with 2 internal ground planes is used. Looking at the docs...
Using:
NRF9151
TF-M enabled
NCS 3.2.2
I'm trying to find more space for my heap on the nrf9151 and I'm disappointed that with a minimal implementation of TF-M...
