Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hello everyone!
I’m working with the Seeed Studio XIAO BLE Sense to acquire data from its integrated IMU (LSM6DS3TR-C) .
I found that the Zephyr SDK (nRF Connect 2.9.0...
Hello,
I'm using devkit board nrf52832dk and nRF SDK v2.7.0.
I would like to generate TX modulated bursts using radio test sample https://github.com/nrfconnect/sdk-nrf...
I'm trying to add a static partition that lies between the mcuboot and mcuboot_pad/app ones, but even though my solution builds correctly, mcuboot is stuck in a loop. This...
Hi,
I'm setting up the project(VS Code + Make + ARM-GCC) for nRF52840. The project will use nRF5 SDK(not new with Zephyr) and softdevice(both BLE roles).
Until now I've...
Hello,
I'm developing a project based on the NRF5340 and have encountered some challenges. As I'm relatively new to C, I'm trying to implement a quadrature (incremental...
Hi,
I was just sent at nRF9160DK from a client to have a play with and test modem functionality for a future product in development.
I have followed the get started instructions...
Hello everyone,
I have some questions regarding the active discharge of the load switch in LDO mode. We have an in-house hw with the nPM1300 configured as described in the...
HI
.
It was configured to detect low voltage of the battery using lpcomp.
This configuration is already being used in mass production of other products and there have...
Hello guys,
I was refreshing BLE concepts by doing the BLE Fundamentals once again and I have faced some trouble with the nRF5340 dk on Lesson 2. I have built the application...
Hi,
we have nRF54H20DK (SoC rev. "C"). connected to MAX77655 via I2C (SCL ~ P1.0, SDA ~ P1.4 according to I2C restriction).
I am trying to test i2c131 for reading/writing...
Hello,
We are using DFU target library with MCUboot (Connect SDK v2.9.0):
And we are getting assertion fail on first dfu_target_offset_get() call after FW update:
...
Please confirm whether the "sample app nrf5340_audio" in "v2.8.0" supports "GAIN control" in "SPI+GPIO mode". the method to enable "GAIN control" in "SPI+GPIO mode" if the...
Hi Nrodic，
Does NRF5340 have an example code for QSPI driving uLED display peripherals (for example, I need to drive this display chip: JBD013VGA， As per the attached...
I'm following along with the Nordic Academy tutorial for v2.7.0-v2.9.0. I made the recommended modifications to my v2.9.0 project with an nRF54L15-DK target:
Create sysbuild...
Hello! I am developing my own BLE solution where I have the different attributes in my service and I am connecting two different nrf52840, one to act as a GATTClient and one...
