When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
NCS 3.4.0 - Thingy91X
If I configure the sysbuild with sysbuild.conf
SB_CONFIG_BOOTLOADER_MCUBOOT=y SB_CONFIG_SECURE_BOOT_APPCORE=n
it builds, but on "west flash" I...
Hi,
1.What is the maximum rate that the QSPI of nRF54L15 can achieve? 2. Is it possible for me to use QSPI to read the flash memory while simultaneously refreshing the screen...
Hi,
I want to ask if the Nrf54l05 supports application image compression. I asked Nordic AI and they said it’s not supported, but I want to know the reason why it’s not...
I'm setting up a board I just built in NCS, and I made an overlay file for it. Specifically, I am setting up the UART21 peripheral and assigning pin outputs. I made a mistake...
I have a school assignment revolving a technological product, where i need to ask a few questions to a business about their involvement with the product. Therefore i need...
I installed NRF Connect, the BLE plugin, and successfully flashed the dongle firmware. IIn NRF connect, the BLE plugin scan button is disabled. 'Quick Start' was unable to...
I want to use the nRF5340 in Thingy:91x to control the external flash (256M bit) and pariition it as LittleFS. I can be sucessfully create partition in nRF5340DK but cancan...
Dear Nordic support,
We are bringing up LE Secure Connections as a GAP Central on nRF52832 with SoftDevice S332 (BLE + ANT, nRF5 SDK 14, BLE API v5). The nRF runs the serialization...
Dear Nordic Team,
Test_1:
I am trying to use IEEE 802.15.4 PHY test tool app to test the RF performance of the custom nrf54l15 module and nrf54l15dk kit.
Setup:
CMD...
NCS 3.4.0 - Thingy91X
Using McuBoot without external flash seems to work not anymore.
According nrf/sysbuild/Kconfig.sysbuild:
config PM_EXTERNAL_FLASH_MCUBOOT_SECONDARY...
Hi,
I have got nRF54LM20-DK with the nRF7002-EBII add-on. I would like to know is there any recommended camera add-on for this hardware to develop vision based AI solutions...
In nRF cloud, in the device list ( https://app.nrfcloud.com/#/devices ) it is difficult to manage larger number of devices because of lack of search and limited sorting. ...
i'm looking for a simple example which i can run on nRF9151 DK (v0.9.0) where i can profile power consumption....
ideally, the example would repeatedly send packets over...
Hi, We have a BLE peripheral on nRF52833-QIAA (custom board based on nrf52833 ) building with NCS 2.8.0 , sysbuild, extended advertising, GATT, a prebuilt custom bootloader...
