Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Somewhat related to this:
I'm wishing to optimise code (removing a load of volatiles) by ensuring most of my application code runs at the same interrupt as the NRF_SDH_BLE_OBSERVER...
Hi,
I have 2 problems in power profiler kit II:
Problem 1: When I connect the porfiler kit II to the computer, the computer can't identify the PPK2
Porblem 2: The output...
I want to know how to adjust the TX RX setting for the nRF52833 DK connected to the nRF21540 EK shield. I have already added -DSHIELD="nrf21540ek" to the build configuration...
Hello.
I am trying to repeat the functionality of the project that is shown in this video https://www.youtube.com/watch?v=fCU8x-pmtqU&list=PLx_tBuQ_KSqG-leiJDfOKf_ZmCqHnbi4r&index...
We are using SDK v2.6.1 for our application, along with the Fanstel module WT02C40C.
Internet connectivity is provided to the WT02C40C module via a hotspot, with CONFIG_STA_KEY_MGMT_WPA2...
The "nRF Command Line Tools" page, https://www.nordicsemi.com/Products/Development-tools/nrf-command-line-tools says " Important: The nRF Command Line Tools is in the process...
I want to interface 3 custom made heater boards to nrf5340dk. Where the simple task is to toggle gpio's to Turn ON & OFF the heater board. Now, we are using P 0.01, 0.02 &...
Hello, I am considering the prospect of using channel sounding as opposed to UWB for indoor asset tracking. I can understand, that the main limitation with that would be,...
Hi There:
I used the nRF7002 DK to evaluate its WiFi throughput performance.
The test environment is below:
1. nRF7002 DK
2. NCS version: 2.5.0
3. Sample application...
Hello Everyone,
I have configured SPI1 at 1MHz, to receive data with a sensor. Basically i am reading data from a sensor device. So calling spi_transceive_dt() with 4...
The current specifications (v0.8) for the nRF54L series of parts provide very little information about the input impedance of the SAADC peripheral. There are no values specified...
hey i am using a custom nrf52840 board and i keep my device on by setting a gpio pin high and device turns off as soon as it sets to low .
during ota update when the bootloader...
Hi,
I have a firmware project that was originally developed for an nRF52833. It successfully mounts LittleFS on 3 partitions in external flash. For the nRF52833 I was simply...
Dear Devzone!
I am trying to add AES-128 decryption support for secure DFU with cc310_bl backend. However when I call nrf_crypto_aes_update it never returns. Examining the...
