Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
HI,
I want to use nrf52833 for receiving SAADC DATA in my phone by using BLE_NUS_DATA_SEND.
Here are my codes.
In 716 ~ 724 lines, I added codes about BLE_NUS_DATA_SEND...
Hello
I'm using the nrf52840 DK with sdk version of 15.0.0.
My requirement is to flash my project through cli commands, so I have followed the following steps in below...
Hi,
I recently updated my toolchain using the nRFConnect tool chain manager.
(I was seeing problems after an OS update)
This update fixed my problem but when I build...
Hi,
Please, what are the settings for gpio driver in sdk15.2. for some gpio pin to be able to sink current (to act as gnd? ). In my project it is used for loadswitch enable...
Hi,
I have bumped into this bug in SDK v17.0.0 and SDK v17.0.2 but no fix yet.
We are using nRF52840 with S140.
Can you please make sure to release this fix asap because...
Hi There - My question is about the nrf5340 dual core cpu. I’d like to know if it is possible to have one core polling sensors on the spi bus - then pass this data to the...
Hello
I am testing sending the value to the app through the ble_app_uart of SDK v17.
I know roughly that I need to use 'ble_nus_data_send', but it is not printed from...
I add this code in 'static void on_connect(ble_nus_t * p_nus, ble_evt_t const * p_ble_evt) ' on the sever. But I still got an err_code NRF_ERROR_INVALID_DATA. Softdevice is...
Hello,
I want to compile the "pca10040" template after installing the SDK and the command line tools with Segger Embedded Studio, but I got the error:
cannot find ......
Hi,
Currently our team would like to start using Zephyr for our development, but some colleagues fear that it will use too many resources. They saw that our first test project...
Hello.
I'm using Zigbee SDK 4.1.0 with nrf52840.
When the firmware is configured as Zigbee router, it forwards route request data packets with incorrect contents.
...
Hi,
When I try to compile the gps nrf9160 sample with the SUPL enable, the compilation crash each time.
I get the error "Assertion failed: CONFIG_FP_SOFTABI is not supported...
I want to implement BLE using nRF52840. Without using SDK, we have formed a new project and successfully controlled GPIO control and UART. She wants to use the Softdevices...
I see the NRF8001 doesn't necessarily require the 32.768 Khz oscillator to function. My understanding is it's useful to preserve power. If I'm not worried about power draw...
